# changelog

author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -     *Problems Fixed:**
      
        * Fixed an issue where wear usage was not being reported correctly in the SmartSSD Wear Gauge Utility


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      If Power On Hours exceeds 70,000hrs, PM2R will report Hardware error (04/4C/A8) after the next Power Cycle and will not accept read/write commands. This fix will update storage location reporting when the maximum number of registrations in the Work Load Log read process reaches 70,000; the last registered 70,000th storage location will be modified to be read as the next (70,001st) storage location.
        * For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00111296en_us


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -          * Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode  is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
          * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.
        * Changes some settings to comply with Microsoft Storage Spaces Certification requirements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Drive would stop responding on read retry Step 50 of Controller code correction.
        * In extremely rare cases, internal drive testing found that if I_T nexus loss is greater than 2 seconds, data loss might occur. If this rare condition occurs, the drive reports sense code 06/29/04 (HDD executed internal reboot), which displays on the screen and is entered in the drive log.
      
        * Drive may report sense code 02/04/02 instead of 02/04/01 if MODE SENSE and MODE SELECT command come before drive ready. The drive name will no longer display in the list, and the system will not be able to access the drive until the system is power-cycled or reset.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -     This firmware fixes a condition that could cause the heads to land on the
      media in an emergency power off situation, and eliminates a command timeout
      issue. Some internal logging operations were refined at the same time.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Provides proactive protection against contamination built up on the media and air-bearing surface of the heads by increased routine "sweeping" of the media surface.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Fixed a PSuite FwCheck L5005 error at the time of Support Service Pack for ProLiant (SPP) execution.
        * Fixed a L4500 error at the time of device WWN update.
        * Fixed a write CMD timeout at the time of SPL happens during sanitize.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -     This FW release deploys an Enhanced Media Scan algorithm that addresses an
      issue when the host system does not provide enough idle time for drive's
      Foreground Media Scan to be activated, which is needed to ensure long term
      drive reliability. It also addresses few minor issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK1
changelog:
  -      Firmware corrects an issue where the drive will be in a failed state after an unexpected power loss. When this occurs the drive will not recover after subsequent power cycles and will not be accessible by the system configuration and Host applications.
        * Refer Customer Bulletin for workarounds <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00042733en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK1-2.1
changelog:
  -      Firmware corrects an issue where the drive will be in a failed state after an unexpected power loss. When this occurs the drive will not recover after subsequent power cycles and will not be accessible by the system configuration and Host applications.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      Applied enhanced NAND recovery algorithm to prevent read UECC error
        * Prepare proper response data for Get Message Type Supported MCTP Command


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -      Fixed Store Userdata in Crash Occurred.
        * Fixed Log sense returned incorrect length of data.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      The updates were included in a regularly scheduled 5300 maintenance release. This firmware has a security version upgrade to include TCGe SKUs and prevent a downloading of a back level firmware version of HPG0 after upgrading to HPG1.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -      Reduced the occurrence probability of PMIC busy issue. 
        * Fixed the system data error at the drive power on issue. 
        * When the PLP operation starts, the waiting Unmap request to the 4KB not-aligned host write area is canceled to be able to complete PLP correctly.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG6 do not need to update to HPG6(B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPGE
changelog:
  -      Fix to issue in bootloader download during power loss. 
        * Improvements to error exception.
        * Improvements to Secure lock fix during multi-thread read tests with high freq. power cycling.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4ICRHPK3
changelog:
  -      Fixed issues described in Customer Bulletin at the following URL: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00111900en_us.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 4ICRHPK3-2.1
changelog:
  -      The issue affects SSDs with an HPE firmware version prior to 4ICRHPK3 that may result in SSD failure starting at 4,700 hours of operation, neither the SSD nor the data can be recovered, after the SSD failure occurs.
        * For more information, refer to HPE Customer Bulletin at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00111900en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPG1. 
        * This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG1 do not need to update to HPG1 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-2.1
changelog:
  -     *Enhancements/New Features for HPG1 (B):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG1 do not need to update to HPG1(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1-3.1
changelog:
  -      Added support for SmartRAID 3154-8e RAID controller.
        * Added support for HPE Smart Array P824i-p MR Gen10 controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -      This firmware updates the drive to indicate NDU compliance.
        * Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      This firmware includes a fix for an issue where the LED would continue blinking after a Sanitize operation completed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      The new firmware improves robustness during dual port heavy workload environments for both runtime and after sudden power off events.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      Firmware version HPD5 fixes an issue where drive may fail with command timeout messages.  This condition may occur within a few days of initial use if a very small amount of data is written to the drives and they are left powered on without additional data being written to the drive.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc...


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc...


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7-5.1
changelog:
  -      Online firmware flashing of drives attached to aSmart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiantand Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like(B) (C) (D) etc...


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Improved Product Quality and Reliability. Changed Cap Charge Timeout to 14 seconds from 4 seconds to provide additional time for cap charge in marginal power environment.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -      New servo which disables a feature that could cause unrecoverable data errors. 
        * A fix to prevent the drive from becoming unresponsive during certain mixed read/write random workloads.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -     This firmware version updates the Vendor ID in the standard inquiry to 'HPE',
      in previous versions it was 'HP.'


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Increased Queue Size from 32 to 128 to be equal to the max number of chips.
        * Refresh NM SRAM area periodically only when idle as a possible work around on NM SRAM parity error.
        * Change the error response as 0x3 (SP_Busy) or 0x07 ( NO_SESSION_AVAILABLE) when host attempts to open another session while a session is already opened.
        * Disable verify compare if APP_CHK=0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -     *Problems Fixed:**
      
        * Fixed an occasional and potentially significant delay in completion time of the SANITIZE function, along with alignment of some settings, features and internal logging with specifications.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-3.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG5 do not need to update to HPG5(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6-2.1
changelog:
  -      Corrects some internal diagnostic logging and reporting functions.
        * Streamlines internal buffer management.
        * Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8
changelog:
  -      Eliminates a potential hang on 4TB under certain pattern-dependent read conditions
        * Eliminates the possibility of a weak read signal under a sequenced combination of read/write conditions
        * Provides reliability enhancements involving head fly height dynamics
        * Enables download Mode 0Eh activation by Mode 0Fh


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2-4.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations. 
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager. 
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      This firmware adds a feature that will periodically assess the health of the writer element of the head by verifying the data after a write operation to ensure more robust data integrity.
        * When performing format on drives with marginal servo flaws, it takes too long to format or format fails with 03/31 reported across the interface on subsequent commands. This firmware includes a change that moves the servo flaw characterization retries earlier in the sequence of format.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8-2.1
changelog:
  -      Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      Fixes an issue where the drive may become unresponsive and stop functioning under certain initial usage conditions (eg, idle, low workloads, or continuous system reboot).
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00041830en_us>.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -     Firmware version HPG3 addresses the following issues:
      
        * Corrects the potential for drives to become unresponsive. For details about this issue, refer to HPE Customer Bulletin: HPE Solid State Drives (SSD) - SSD FIRMWARE UPGRADE REQUIRED to Prevent a Higher Than Expected Failure Rate Noted on Certain Model SSD Drives: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00048133en_us>.   
        * Improves drive reliability by including the latest firmware maintenance updates.  
        
      After HPG3 firmware is downloaded to the drive, the new HPG3 firmware will be
      active on the drive. The new drive bootloader code will be activated after the
      next drive power cycle.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-3.1
changelog:
  -       
        * Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or Host Bus Adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..,


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-3.1
changelog:
  -     Firmware version HPG3(C) addresses the following issue :
      
        * Added a fix for changing the order of write buffer modes in the flash engine.
      
      Firmware version HPG3 addresses the following issues:
      
        * Corrects the potential for drives to become unresponsive. For details about this issue, refer to HPE Customer Bulletin: HPE Solid State Drives (SSD) - SSD FIRMWARE UPGRADE REQUIRED to Prevent a Higher Than Expected Failure Rate Noted on Certain Model SSD Drives: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00048133en_us>.   
        * Improves drive reliability by including the latest firmware maintenance updates.  
        
      After HPG3 firmware is downloaded to the drive, the new HPG3 firmware will be
      active on the drive. The new drive bootloader code will be activated after the
      next drive power cycle.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      Fixes a rare link loss issue and adds enhancements for drive reliability.
        * After HPG5 firmware is downloaded to the drive, the new HPG5 firmware will be active on the drive.
        * The new drive bootloader code will be activated after the next drive power cycle.
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00072768en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-4.1
changelog:
  -      Fixes a rare link loss issue and adds enhancements for drive reliability.
        * After HPG5 firmware is downloaded to the drive, the new HPG5 firmware will be active on the drive.
        * The new drive bootloader code will be activated after the next drive power cycle.
        * For more information, refer to HPE Customer Advisory at the following URL:<https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00072768en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -     *Problems Fixed:**
      
        * Version HPD4 prevents the potential for incorrect data to be written to the drive under extremely rare circumstances when the drive experiences a hard reset. This issue has only been observed in a rigorous test environment and has NOT been reported in a customer production environment.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD4 do not need to update to HPD4 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Problems Fixed:**
      
        * Version HPD4 prevents the potential for incorrect data to be written to the drive under extremely rare circumstances when the drive experiences a hard reset. This issue has only been observed in a rigorous test environment and has NOT been reported in a customer production environment.
      
      **Problems Fixed for HPD4 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD7. 
      
        * This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.
      
        * This firmware prevents asserts on a sequential write which can result in devices being lost from the configuration. It also preserves persistent reservation through downloads which prevents loss of performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD8
changelog:
  -      This firmware allows the drive to meet the requirements for Azure Stack certification. 
        * This firmware contains a change to the reported drive serial number in VPD page 80. It will now report the same as is displayed on the drive label.  Any removed characters are replaced with blank place holders so the log format will not be changed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -      This firmware includes a fix for an issue that could cause timeout errors during certain sequential write corner cases. There is also a fix for slow response time during random write workloads.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      This firmware includes a fix for an issue where a drive could become format corrupt after a power cycle if write commands were being executed before the power loss.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      New servo which prevents the drive from posting non-media errors.
        * A fix to prevent the drive from becoming unresponsive during certain mixed read/write random workloads.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      This firmware includes a change to reduce response times on random read/write workloads where commands are sent at slow interval (one every few hundred milliseconds).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      Additional improvements in MCTP functionality.
        * Drive fails to train in BL460 after Windows warm reset or iLO reset.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK4
changelog:
  -      Fixed timing issue to pass VMWare VSAN certification.  Downgrading to any previous version of firmware is not allowed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -     *Enhancements/New Features:**
      
        * Improved robustness of Adjacent Track Interference (ATI) mitigation in System.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -     *Problems Fixed:**
      
        * Persistent Write Cache release size was miscalculated when disk write operation completed before command complete was reported to host which could result in slow sequential write performance of the drive.
        * Drive would stop operations when disk received COMRESET command during firmware download (DOWNLOAD MICROCODE command).  
      NOTE: If this error occurs, data integrity is maintained and reboot is
      required to restart the drive operation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG7
changelog:
  -      This firmware revision improves low-temperature performance and Error Correction Code (ECC) error recording for some commands. 
        * It also improves internal logging capabilities for failure analysis.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8
changelog:
  -      Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware contains a change to prevent occasional command completion times in the 4-5 second window when command is received just as the drive is transitioning from active to Idle A.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Online firmware flashing of drives attached to an HP Smart Array controller running in Zero Memory (ZM) mode or an HP ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Enhancements/New Features:**
      
        * Improved performance at higher drive temperatures.
        * Improved link error rate counter accuracy before PHY was ready.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * HPD2 firmware update resolved an issue in multiport systems where the hard disk drive (HDD) might not be recognized. This issue was due to the HDD responding too slowly to a link reset on port A if port B was unavailable (multiport failover condition).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-2.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD4 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * ****Customers who already installed firmware version HPD4 do not need to update to HPD4 (C).****


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4-3.1
changelog:
  -     *Enhancements/New Features for HPD4 (C):**
      
        * Adds support for HPE ProLiant Gen10 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6
changelog:
  -      Fixes a data integrity risk where a recoverable error can prevent a write command from completing properly.
        * Fixes a data integrity risk due to incorrect re-ordering of commands, when overlapped commands occur. 
        * Fixes a data integrity risk during very large blocks of sequential commands with a data transfer between 1020MB and 1024MB.
        * Fixes a data integrity risk during a sequential read and write workload when a recovered error is encountered, which could cause incomplete data to be read.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD6-3.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager**
        * **Customers who already installed firmware version HPD6 do not need to update to HPD6(C).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     This firmware includes
      
        * New servo which prevents the drive from posting non-media errors
        * A fix for an issue where the drive could become unresponsive after a hard reset


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      The FW version is Changed from HPG0 to HPG1. Changed the thermal throttling scheme. SMART 60 was matched with Tcase 70 and Run the thermal throttling at SMART 65.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-5.1
changelog:
  -      This firmware corrects a potential issue where the data in the reserved tracks is not properly updated, eliminating the risk of a drive not finishing the boot process on power up.  This firmware is also designed to prevent any previous firmware revisions to be loaded onto the drive, once the HPG4 firmware is downloaded.  Other maintenance fixes and updates are also included with the new firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      This firmware corrects a rare but potential data integrity issue, found in specific workloads with improperly ordered write commands or during overlapped read command processing.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Corrects a potential unresponsiveness during a Secure Erase operation, and fixes an incorrect error reporting issue during certain SATA protocol transfers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      HPG6 introduces bug fixes, reliability enhancement and modification in SMART Attributes. Once HPG6 is downloaded, the drive cannot be changed back to an earlier firmware (eg, HPG3).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      This firmware changes some settings to comply with Microsoft Storage Spaces Certification requirements.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Free up more DRAM for user data to improve DRAM management.
      
        * Drive would stop responding on read retry Step 50 of Controller code correction.
      
        * In extremely rare cases, internal drive testing found that if I_T nexus loss is greater than 2 seconds, data loss might occur. If this rare condition occurs, the drive reports sense code 06/29/04 (HDD executed internal reboot), which displays on the screen and is entered in the drive log.
      
        * Drive may report sense code 02/04/02 instead of 02/04/01 if MODE SENSE and MODE SELECT command come before drive ready. The drive name will no longer display in the list, and the system will not be able to access the drive until the system is power-cycled or reset.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -     This firmware provides a change to the Vendor ID in the VPD page that refers
      to HP instead of HPE.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD7
changelog:
  -     This firmware fixes a condition that could cause the heads to land on the
      media in an emergency power off situation, and another condition that can lead
      to high-fly write, and eliminates a command timeout issue. Some internal
      logging operations were refined at the same time.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4
changelog:
  -      This firmware release provides additional protections against hangs in certain corner cases, and cleans up some error handling and command behavior issues.
        * It also fixes a firmware bug that caused significant performance degradation in abnormally long data transfers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-2.1
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode  is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG4-3.1
changelog:
  -      Online firmware flashing of drives attached to aSmart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiantand Smart Update Manager.
        * Customers who already installed latest firmware version do not need to update to sub version like(B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode  is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
        * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for ProLiant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -      Improvement in mixed READ/WRITE performance, which was causing a field issue at an HPE customer


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG6
changelog:
  -      Improvement in mixed READ/WRITE performance, which was causing a field issue at an HPE customer - Improve random mix performance in TL=2048k and 512k


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-2.1
changelog:
  -          * Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
          * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.
          * Customers who already installed latest firmware version do not need to update to sub version like (B) (C) (D) etc..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK2
changelog:
  -      Fixes an issue where the SSID was not programmed correctly to the drive. This may cause issues with the drive not being identified correctly in the Integrated Lights Out Utility.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPK3
changelog:
  -      Fixed SSD weargauge report error issue.
        * Fixed Assign FWState as TR_DONE_ERR at the correct location.
        * Prepare proper response data for Get Message Type Supported MCTP Command.
        * Added code to preserve current feature values cross live firmware update.
        * Allocate 4 bytes instead of 2 bytes for parameter code.
        * Changed the value for NLB equal to NSize -1.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      Addresses a hot plug reporting concern
        * Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Fix issue with Drive Hang on Read Retry Step 50 Controller code correction - When "command aging timer expire" AND "I_T nexus loss" occurs at the same time, HDD reports sense code, 06-29-04 Sense code correction.
        * Drive may report sense 02/04/02 instead of 02/04/01 if MODE SENSE and MODE SELECT command come before drive ready.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG1
changelog:
  -      Fixes Addressed a sustained write performance by improving the efficiency of background tasks. - Addressed a rare occurrence of a data loss issue during a sudden power event. - Addressed a rare occurrence of a Data Management Error after an interface reset when the device's Software Setting Prevention (SSP) is disabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      Fixed an issues where work load logging tasks were not properly reported.
        * Fixed an issue where temperatures below 10 degree celsius were being shown as a high temperature.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Fixed a bug which is related to SSDs returning unexpected data when drive statistics are queried and could result in server instability.
        * For more information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00097984en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -      Improves data integrity
        * Decreases possibility of data corruption in certain error and timing conditions
        * Reduces the probability of hangs and provide a minor performance improvement


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> MPK71H5Q
changelog:
  -      Improve overhead in handling of first packet to limit the incidence of NACKs due to lost byte from second packet
        * Maintain Class Code value in a buffer area when link is down. Copy maintained Class Code from buffer to PCIe Config Space on link-up
        * Change 'Percent Endurance Used' value reported in a Workload Log Page ( D6h ) to report actual endurance value


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> MPK73H5Q
changelog:
  -      Optimized T-offset setting .
        * Change MQES setting to 8192.
        * Code change to set 'Slot Clock Configuration bit in Link Status register.
        * Fixed LED Behavior misaligned specs issue.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> MPK75H5Q
changelog:
  -      Fixed False UECC issue at idle power mode (12.8TB and 15.36TB only).
        * Apply PCLK running PHY option, PLL clock disable can be avoided in lane 0 missing case.
        * Old FW download Blocking.
        * FW is changed off the option of TX data alignment for each lane.
        * FW is changed to clear the interrupt after TLP Complete when PCIe config read operation.
        * For more information, refer to HPE Customer Bulletin at the following URL: <https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00113342en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      This firmware has a change that allows the drive to meet the requirements for Microsoft Azure Stack certification.  It also includes a fix for an issue that could cause timeout errors during certain sequential write corner cases.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -          * Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode is NOT supported. Only offline firmware flashing of drives is supported for these configurations.
          * Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3
changelog:
  -     *Problems Fixed:**
      
        * After HDD power cycle, the Background Media Scan (BGMS) pointer would invoke a second BGMS routine starting at LBA 0, which could affect  performance until the second BGMS has completed.
        * When writing to the HDD after it entered or returned from a standby state, the potential existed for a Non Volatile Cache issue to occur..


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPG3 do not need to update to HPG3 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG3-2.1
changelog:
  -     *Problems Fixed:**
      
        * After HDD power cycle, the Background Media Scan (BGMS) pointer would invoke a second BGMS routine starting at LBA 0, which could affect  performance until the second BGMS has completed.
        * When writing to the HDD after it entered or returned from a standby state, the potential existed for a Non Volatile Cache issue to occur..
      
      **Problems Fixed for HPG3 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPG5.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG5-2.1
changelog:
  -      **Online firmware flashing of drives attached to a Smart Array controller running in Zero Memory (ZM) mode or a ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the Service Pack for Proliant and Smart Update Manager.**
        * **Customers who already installed firmware version HPG5 do not need to update to HPG5 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG8-2.1
changelog:
  -      This firmware updates the drive to indicate NDU compliance.
        * Fixed the issue of Online firmware update fails when drives are connected behind AHCI controller.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD9
changelog:
  -      Fixed Store Userdata in Crash Occurred
        * Fixed Log sense returned incorrect length of data.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -      **Online firmware flashing of drives attached to an HPE Smart Array controller running in Zero Memory (ZM) mode or an HPE ProLiant host bus adapter (HBA) is NOT supported. Only offline firmware flashing of drives is supported for these configurations.**
        * **Online drive firmware update available for Smart Array Controllers configured in systems running supported Linux, Microsoft Windows, and VMware environments. All other OSes would require an offline update using the SPP and HP SUM.**
        * **Customers who already installed firmware version HPD5 do not need to update to HPD5 (B).**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5-2.1
changelog:
  -     *Problems Fixed:**
      
        * Self-initiated reset during ATI (Adjacent Track Interference) mitigation issue, where the drive reported a 06/29/04 (Self-Initiated Reset) to the controller.  Then the controller would re-establish link with the drive and resend the command.
        * Servo miscalculations that resulted in degraded drive performance.
      
      **Problems Fixed for HPD5 (B):**
      
        * Component would fail to install drive firmware for drives present in a system configured with two or more external drive enclosures attached to an HP Host Bus Adapter H22x. The following message would be reported in the component log file - "Device appears more than once in tree". The drive firmware installation failure was not observed in configurations having only one external drive enclosure attached to an HP Host Bus Adapter H22x.
        * Component fails to update the firmware for drives connected behind an HP Smart Array P431 controller. Component reports the firmware update was successful. However, after a power cycle, the firmware version remains unchanged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPG2
changelog:
  -      When SSD statistics are queried, erroneous drive temperatures may be reported. When this occurs, the system may encounter any of the two following conditions, leaving the server in an unstable state. 
          * Server shutdown
          * In VMware vSAN environment, storage volume taken offline.
        * For important information, refer to HPE Customer Advisory at the following URL: <https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00097984en_us>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -      Fixes the cause of internal reboots detected in the MSA system.
        * Removes a vendor unique sense code that the controller does not handle properly.
        * Includes changes to eliminate the cause of a potential hang condition.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3
changelog:
  -      Fix issue with drive Hang on read retry Step 50 Controller code correction - When "command aging timer expire" AND "I_T nexus loss" occurs at the same time, HDD reports sense code, 06-29-04 Sense code correction.
        * Drive may report sense 02/04/02 instead of 02/04/01 if MODE SENSE and MODE SELECT command come before drive ready.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      There is no compelling reason to update this firmware. Risk is that whoever looks at the Vendor ID in the VPD page will notice that it refers to HP instead of HPE. There is no functional risk if not upgraded.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD1
changelog:
  -     *Problems Fixed:**
      
        * This firmware improves HDD reliability when HDDs are exposed to long periods of host inactivity that exceed 1 second. HDDs may become unresponsive when using HDD firmware prior to version HPD1.  This firmware also contains a change which prevents an incorrect reassign status of a repaired sector from being logged.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD2
changelog:
  -     *Problems Fixed:**
      
        * This firmware prevents asserts on a sequential write which can result in devices being lost from the configuration. It also preserves persistent reservation through downloads which prevents loss of performance.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD3-2.1
changelog:
  -      This firmware allows the drive to meet the requirements for Azure Stack certification. 
        * This firmware contains a change to the reported drive serial number in VPD page 80. It will now report the same as is displayed on the drive label.  Any removed characters are replaced with blank place holders so the log format will not be changed


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD4
changelog:
  -      This firmware release provides a more graceful termination of certain commands and prevents a read/write command hang under an unusual timing condition when resuming from a suspend operation


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> HPD5
changelog:
  -      This firmware release provides additional protections against hangs in certain corner cases, and cleans up some error handling and command behavior issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.2.6
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where HPE Jitter support may not respond to configuration
      changes from the Integrated Lights-Out webpage.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.4.4
changelog:
  -     *Important Notes:**
      
      This is a new release of HPE Gen10 Innovation Engine (IE) Firmware revision
      0.1.4.4. System ROM V1.26 must be installed prior to updating to IE FW
      0.1.4.4. This revision of the IE FW is required for updating the Intel
      Platform Service (SPS) Firmware revision 04.00.04.288 and later. It should be
      installed prior to updating to SPS FW 04.00.04.288 or later. SPS FW
      04.00.04.288 mitigates security vulnerability CVE-2017-5706
      (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5706) and
      CVE-2017-5709 (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5709).
      It is anticipated that details regarding these security vulnerabilities will
      be published to these links on November 20,2017. These security
      vulnerabilities are not unique to HPE servers.  
      
      **Firmware Dependencies:**
      
      System ROM V1.26  
      
      **Problems Fixed:**
      
      This is a new release of HPE Gen10 Innovation Engine (IE) Firmware revision
      0.1.4.4. System ROM V1.26 must be installed prior to updating to IE FW
      0.1.4.4. This revision of the IE FW is required for updating the Intel
      Platform Service (SPS) Firmware revision 04.00.04.288 and later. It should be
      installed prior to updating to SPS FW 04.00.04.288 or later. SPS FW
      04.00.04.288 mitigates security vulnerability CVE-2017-5706
      (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5706) and
      CVE-2017-5709 (http://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5709).
      It is anticipated that details regarding these security vulnerabilities will
      be published to these links on November 20,2017. These security
      vulnerabilities are not unique to HPE servers.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.5.2
changelog:
  -     *Important Notes:**
      
       HPE Innovation Engine (IE) Firmware 0.1.4.4 has been removed from the web for
      the following reasons:
      
      1\. Systems could experience a rare issue where processor and memory
      temperatures stop reporting, resulting in increased system fan speeds. This
      issue is seen during a system reboot and is only recovered by another system
      reset. This issue did not exist with previous versions of the Innovation
      Engine Firmware.
      
      2\. Systems configured with Jitter Smoothing support could experience a rare
      issue where on a given boot the functionality does not function. Resetting the
      system typically corrects the issue. This issue did not exist with previous
      versions of the Innovation Engine Firmware.
      
      3\. Systems configured with the Intel Xeon Scalable 6143 Gold and 8165
      Platinum processors with HPE's Core Boosting support enabled could experience
      a rare issue where on a given boot the functionality does not function.
      Resetting the system typically corrects the issue. This issue did not exist
      with previous versions of the Innovation Engine Firmware.
      
      This is a new release of HPE Gen10 Innovation Engine (IE) Firmware revision
      0.1.5.2 to replace IE version 0.1.4.4. If updating from IE version 0.1.4.4,
      follow the installation notes. If updating from an IE version prior to 0.1.4.4
      please read the following note.
      
      System ROM V1.26 must be installed prior to updating to IE FW 0.1.5.2. This
      revision of the IE FW is required for updating the Intel Platform Service
      (SPS) Firmware revision 04.00.04.288 and later. It should be installed prior
      to updating to SPS FW 04.00.04.288 or later. SPS FW 04.00.04.288 mitigates
      security vulnerability CVE-2017-5706 (http://www.cve.mitre.org/cgi-
      bin/cvename.cgi?name=2017-5706) and CVE-2017-5709 (http://www.cve.mitre.org
      /cgi-bin/cvename.cgi?name=2017-5709). The details regarding these security
      vulnerabilities were published to these links on November 20,2017. These
      security vulnerabilities are not unique to HPE servers.
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later  
      
      **Problems Fixed:**
      
      Addressed an issue where systems configured with Innovation Engine Firmware
      0.1.4.4 could experience a rare issue where processor and memory temperatures
      stop reporting, resulting in increased system fan speeds. This issue is seen
      during a system reboot and is only recovered by another system reset. This
      issue did not exist with previous versions of the Innovation Engine Firmware.
      
      Addressed an issue where systems configured with Innovation Engine Firmware
      0.1.4.4 and Jitter Smoothing support could experience a rare issue where on a
      given boot the functionality does not function. Resetting the system typically
      corrects the issue. This issue did not exist with previous versions of the
      Innovation Engine Firmware.
      
      Addressed an issue where systems configured with Innovation Engine Firmware
      0.1.4.4 and the Intel Xeon Scalable 6143 Gold and 8165 Platinum processors
      with HPE's Core Boosting support enabled could experience a rare issue where
      on a given boot the functionality does not function. Resetting the system
      typically corrects the issue. This issue did not exist with previous versions
      of the Innovation Engine Firmware.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.6.1
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later
      
      **Problems Fixed:**
      
      Addressed an issue where the Integrated Lights-Out (iLO) web interface may
      incorrectly report the Innovation Engine is running in a degraded state.
      
      Addressed an issue where memory telemetry data may not be reported properly in
      the Integrated Lights-Out (iLO) web interface or through the HPE RESTful API.
      
      Addressed an issue where the Innovation Engine Firmware flash would fail if a
      previous flash attempt was interrupted and not completed successfully.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.1.6.1-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 0.1.6.1(C) contains updates to the component packaging and is
      functionally equivalent to ver. 0.1.6.1.  It is not necessary to upgrade with
      Revision C if a previous component Revision was used to upgrade the firmware
      to version 0.1.6.1.
      
      **Firmware Dependencies:**
      
      System ROM V1.26 or later  
      
      **Problems Fixed:**
      
      Addressed an issue where the Integrated Lights-Out (iLO) web interface may
      incorrectly report the Innovation Engine is running in a degraded state.
      
      Addressed an issue where memory telemetry data may not be reported properly in
      the Integrated Lights-Out (iLO) web interface or through the HPE RESTful API.
      
      Addressed an issue where the Innovation Engine Firmware flash would fail if a
      previous flash attempt was interrupted and not completed successfully.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.0.11
changelog:
  -     Added support for Intel Xeon Scalable Performance 3200, 4200, 5200, 6200 and
      8200 series processors.
      
      Added support for HPE system performance monitoring and workload performance
      advisor. This feature also requires Integrated Lights-Out (iLO) firmware
      version 1.40 or later.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.0.11
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where updates to the Intel Server Platform
      Services (SPS) firmware may fail.
      
      **Known Issues:**
      
      This flash component will report the Current Revision of the Innovation Engine
      FW as "n/a" when updating the Innovation Engine FW. This does not affect the
      flash update or impact how the Innovation Engine FW operates.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.1.2-2.1
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Enhancements/New Features:**
      
      Added support for HPE Persistent Memory featuring Intel Optane DC Persistent
      Memory.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.2.0
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where Processor or Memory temperature
      reporting may not be collected properly by the platform and the system fans
      may be running faster than expected. This issue has been seen occasionally
      after a server reboot and is typically corrected with a subsequent server
      reboot.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.2.2
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an extremely rare issue where processor or memory temperature
      reporting may stop reporting properly or report a constant reading after
      servers have been operating over an extended period of time without an AC
      power cycle.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.2.3
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Address an issue where Innovation Engine (IE) Firmware may be unresponsive and
      iLO Firmware may report "Update Failed" after flashing the Innovation Engine
      (IE) Firmware via RESTful update.  The flash will have been performed
      successfully, but the system must be reset for IE Firmware to function
      properly.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.3.0
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours. On some systems this could result in a brief drop in CPU utilization or
      network traffic lasting less than a second.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 0.2.3.0-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 0.2.3.0(C) contains updates to the firmware packaging and is functionally
      equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision B if
      a previous component revision was used to upgrade the firmware to version
      0.2.3.0.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours. On some systems this could result in a brief drop in CPU utilization or
      network traffic lasting less than a second.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0.22
changelog:
  -     *Important Notes:**
      
      None
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0.22-3.1
changelog:
  -     *Important Notes:**
      
      Ver. 1.0.0.22(C) contains updates to the firmware packaging and is
      functionally equivalent to ver. 1.0.0.22. It is not necessary to upgrade with
      Revision B if a previous component revision was used to upgrade the firmware
      to version 1.0.0.22.
      
      **Firmware Dependencies:**
      
      None
      
      **Problems Fixed:**
      
      Addressed an issue where Innovation Engine (IE) may improperly reset every 24
      hours.
      
      **Known Issues:**
      
      None


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.10
changelog:
  -     Initial iLO 5 release with the following features:
      
        * The iLO Service Port on the front of the server is new on Gen10 ProLiant servers and Synergy compute modules. Use this feature to connect a client directly to the server to access the iLO web interface, remote console, CLI, or scripts. You can also connect a USB key and download the Active Health System log to a supported USB flash drive.
        * Improved HPE Agentless Management support for out of the box SNMP-based server management that does not require OS-based agents. OS-based agents are not supported on Gen10 servers.
        * Improved secure firmware update and recovery.
        * Secure Start ensures firmware integrity for essential system firmware.
        * Runtime firmware verification scans essential system firmware for further system integrity.
        * Automatic secure recovery of essential system firmware.
        * Common Access Card (CAC)Smartcard authentication.
        * New user account privilege levels. Specific privileges for BIOS, Storage, and Network configuration.
        * Virtual Media performance is typically at least twice as fast as it was with iLO 4.
        * New iLO web interface design.
        * Expanded Redfish support.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11
changelog:
  -      This firmware release is intended for FIPS 140-2 (level 1) validation and Common Criterial (EAL 2+) certification. For the status of both, go to http://csrc.nist.gov/groups/STM/cmvp/validation.html for FIPS and http://www.commoncriteriaportal.org/ for Common Criteria. Search for "iLO 5".
        * Updated cryptographic stack as required by FIPS inspection and validation process.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15
changelog:
  -     Users should update to this firmware version if their system is  
        affected by one of the documented fixes or if there is a desire to utilize
      any  
        of the enhanced functionality provided by this version.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15
changelog:
  -      iLO backup and restore--This feature allows you to restore the iLO configuration on a system with the same hardware configuration as the system that was backed up. For example, you could use this feature if the system board is replaced, an accidental or incorrect configuration change occurred, or iLO was set to the factory default settings.  This feature is not meant to duplicate a configuration and apply it to a different iLO system.
        * AMD platform support
        * Support for diffie-hellman-group-exchange-sha256.
        * Support for multiple destination AlertMail email addresses. Enter the addresses separated by a semicolon.
        * iLO RESTful API features: 
          * Aux Power Reset
          * Jitter Control features to get and set Jitter Control Mode and Frequency
        * New iLO RESTful API properties to bridge the gap between RIBCL and iLO RESTful API features: 
          * High Efficiency Mode
          * Encryption-related properties and Cache Module Serial Number
          * Login Security Banner
          * Current Power on Time (provides the time since the system was last powered on).
          * Persistent Mouse/Keyboard Enabled
        * New iLO RESTful API  events for NVDIMM Init Error and Runtime Firmware Authentication Error.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15
changelog:
  -      No traps from the System Management Assistant are received when SNMP is disabled in the  iLO web interface.
        * The power profile cannot be changed through the iLO web interface.
        * Network transmission graph data is not populated in Active Health System logs.
        * The NVDIMM firmware version is not displayed on the iLO web interface Installed Firmware page.
        * The iLO web interface intermittently displays incorrect memory status after a system reset.
        * The iLO  RESTful API does not provide a method to get current cipher information.
        * The Server Power page stalls when loading the server power information.
        * Nothing happens when you click the Import button on the HPE SSO page.
        * Secure boot cannot be configured through the iLO RESTful API, even if the pending configuration is in UEFI mode.
        * The maximum available power is displayed incorrectly.
        * If the IML contains a maintenance note, the first attempt to clear the log fails.   
        * Certificate-based authentication returns a session URL with inconsistent case.
        * Onetimeboot and Continuousboot do not  take effect in iLOrest.
        * Virtual Media status is not displayed in the Java IRC.
        * The local client keyboard might get disabled when the Java IRC  is in use.
        * An iLO  Federation authentication error might occur when group names with unsupported characters are used in URLs without correct encoding.
        * An issue occurs when copying or restoring certificate mapping entries using fingerprints.
        * An iLO web interface error occurs after an installed certificate was deleted by using the iLO RESTful API.
        * An Internal Error occurs when HPONCFG for Linux is used with a server that uses the SuiteB security state.
        * SNMPv3 user details cannot be modified  through RIBCL.
        * A false positive "Insecure Cache Management Policy" issue is reported by some security scanners.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.17
changelog:
  -     This version adds support for the following features and enhancements:
      
        * iLO Amplifier Pack Server System Restore \- Use the Send Recovery Event button on the Firmware Verification page to send a recovery event to iLO Amplifier Pack. If iLO Amplifier Pack is configured to listen for system recovery events, this event causes iLO Amplifier Pack to initiate the system recovery process.  The system recovery process includes the installation of the System Recovery Set followed by reimaging the server operating system.
        * RESTful API updates: 
          * Added certificate authentication and validation for Virtual Media.
          * Added certificate authentication and validation for RESTful API events that support the iLO Amplifier Pack Server System Restore feature.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.17
changelog:
  -     The following issues are resolved in this version:
      
         SSH does not work correctly when iLO is configured to use the SuiteB
      security state.  
         Importing a certificate does not work correctly after the generation of a
      SuiteB-compliant CSR.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20
changelog:
  -     This version adds support for the following features and enhancements:
      
        * HTML5 Remote Console
        * Shared Network Port IPv6 support
        * Shared Network Port iLO Federation support
        * Ability to associate an SNMP alert destination with an SNMPv1 or SNMPv3 user
        * Enhanced firmware and software update interface: 
          * New Add to Queue pane
          * Remove All option for install sets, queued components, or components in the iLO Repository
          * Recovery Set update option during firmware update, iLO Repository upload, or install queue update
        * CAC Smartcard  authentication support for the Online Certificate Status Protocol (OCSP)
        * iLO RESTful API updates: 
          * NVMe drive properties
          * Remote Support configuration
          * Device Inventory
        * Support for eight SNMP trap destinations
        * SNMPv3 Inform notification support
        * Support for RSA-PSS certificate signatures
        * RSA cipher support in CNSA mode
        * Ability to disable device discovery on Device Inventory page
        * New Service Account option to support user accounts that are used as service accounts for supported applications


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20
changelog:
  -     The following issues are resolved in this version:
      
        * NVMe drive details are not displayed in the iLO web interface for HPE ProLiant XL190r Gen10 servers.
        * The system BIOS version is missing in AlertMail messages.
        * The IPMI Get Chassis Capabilities and Get Chassis Status commands do not reflect the Chassis Intrusion state.
        * Virtual Media devices are inaccessible when two virtual devices are mounted simultaneously.
        * Patched configuration file system.
        * The IPMI pre-watchdog-timeout interrupt does not occur when no watchdog action is selected.
        * Intermittent loss of network interface card (NIC) and drive detection (P408e-m controller) by BIOS on system boot up of HPE ProLiant BL460c servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30
changelog:
  -     Install this update to take advantage of significant improvements to the write
      algorithm for the embedded 4 GB non-volatile flash memory (also known as the
      NAND). These improvements increase the NAND lifespan.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30
changelog:
  -     This version adds support for the following features and enhancements:
      
        * Added support for new platforms: 
          * HPE ProLiant DL20 Gen10 Server
          * HPE ProLiant ML10 Gen10 Server  
        * Improved HTML5 IRC performance, including: 
          * Added virtual keys to improve the ability to send keyboard actions to the server.
          * Added the ability to configure the keyboard layout in the HTML5 IRC
          * Added Virtual Media support for local ISO and IMG files.
        * Firmware and software update enhancements: 
          * iLO users can now view, create, and delete maintenance windows.
          * A new check box allows users to clear the installation queue when initiating an install set.
          * Updated the iLO RESTful API and iLO web interface to report when a reboot is required after an installation task completes.
        * Each time iLO starts, it backs up the iLO configuration to the nonvolatile flash memory (NAND). If the SRAM is erased, the configuration is automatically restored.
        * Added iLO web interface support for Density Optimized Drive Zoning features on supported HPE Apollo products.
        * AlertMail now supports SSL (TLS) for secure email.
        * AlertMail now supports external SMTP mail servers.
        * Added an SNMP trap for when all host NICs are down.
        * Updated to OpenSSL-1.0.2u-fips-2.0.16.
        * Added the list of open source licenses to the login page.
        * Added an SNMP trap for when iLO is reset by IPMI watchdog.
        * Added Intelligent System Tuning features to the iLO web interface. From the iLO web interface, you can view the configured settings, configure Jitter Smoothing, and launch Intelligent Provisioning to configure Workload Matching and Core Boosting.
        * Improved Active Health System logging efficiency to prolong the NAND lifespan.
        * Added iLO health status to the Overview page. If the status is Degraded, this value is also displayed on the Login page.
        * Re-signed the Java IRC to extend the certificate expiration date.
        * Re-signed the .NET IRC to extend the certificate expiration date. 
          * With this enhancement, the .NET IRC requires version 4.5.1 or later of the .NET Framework.
        * Added the ability to remove an SSL certificate and regenerate the iLO self-signed certificate. 
          * Hewlett Packard Enterprise recommends that you install a CA signed certificate.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.30
changelog:
  -     The following issues are resolved in this version:
      
        * Compute modules do not power on after restoring power to Frame.
        * When you use iLO Virtual Media to install an operating system, installation might fail when iLO is configured to use the Shared Network Port.
        * In rare cases, a server runs out of available SSH sessions because the sessions are not reclaimed when a client disconnects.
        * iLO 5 unexpectedly restored itself to the factory default settings when a user did not initiate the process.
        * When Auto Power-On is set to Always Power On or Restore Last Power State, the server might not power on after a cold reset.
        * iLO cannot display the HP Ethernet 1Gb 4-port 331i Adapter MAC address.
        * NVMe drive model numbers are incorrect or inconsistent.
        * Clearing the oemHPE_usercntxt## from the command line clears the value, even though error messages might be displayed.
        * Fixed Single Sign-On when in CNSA mode.
        * Added support for RSA-PSS certificate signatures.
      
      For the latest security bulletins and vulnerabilities, please visit:  
      https://support.hpe.com/hpesc/public/home  
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      http://www.hpe.com/support/ilo5-security-en


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.35
changelog:
  -     This version adds support for the following features and enhancements:
      
        * VGA Port Detect Override--Controls how devices connected to the system video port are detected. Dynamic detection protects the system from abnormal port voltages. This setting is enabled by default, and can be used for troubleshooting cases when there is no video output to displays, KVM concentrators, or active dongles.
        * DHCP Client ID override via iLO RESTful API.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.35
changelog:
  -     The following issues are resolved in this version:
      
        * Fix for improper Smart Array error reported: Cache module board backup power failed.
        * Fixed where iLO may become unresponsive after ejecting virtual media.
      
      SECURITY FIXES:
      
      For the latest security bulletins and vulnerabilities, please visit:  
      <https://support.hpe.com/hpesc/public/home>  
      
        * Security Bulletin HPESBHF03866
      
      Security best practices:
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      <http://www.hpe.com/support/ilo5-security-enn>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.37
changelog:
  -     This version adds support for the following features and enhancements:
      
       \- Ability to backup and to restore a copy of the iLO configuration settings
      to/from iLO non-volatile memory via REST calls.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.37
changelog:
  -     The following issues are resolved in this version:
      
       \- Fix for "VGA Port Detect Override" to show video in all cases where
      monitors are installed.  
       \- Fix for intermittent file upload failures.  
       \- Fix for issues with Virtual Media in FIPS mode.  
       \- Fix for issues with simultaneous use of virtual DVD and floppy in FIPS
      mode.  
       \- Fix for USB floppy when used with ESXi 7 installation driver.  
       \- Fixed potential problem where iLO could continue to interact with system
      memory after it has been released by hpilo module.  
       \- Fix for erroneous reporting of disk drive overheating.  
       \- Fix for intermittent iLO communication error on HPE Apollo 2000.  
       \- Fix for potential RESTful API errors at boot with multiple NICs installed.  
       \- Fix to add iLO 5 NIC information into anonymous XML response.  
       \- Fixed false errors showing link lost on NICs when link never seen in IPMI.
      
      SECURITY FIXES:
      
       \- HPESBHF03894 - HPE iLO5 Local Bypass of Security Restrictions in Firmware
      Update


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.39
changelog:
  -      Fixed issue where pressing UID button on Gen10 server can occasionally cause server to power off


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40
changelog:
  -      Ability to edit Maintenance Windows in Firmware & OS Software section
        * Added Password Complexity feature to Security > Access Settings
        * Enable/disable for overlay video showing Server Health Summary
        * Downgrade Policy - Specifies how iLO handles requests to downgrade any of the firmware types that you can update through iLO. 
        * Virtual NIC functionality (disabled by default)
        * Enabled One-button Secure Erase via Intelligent Provisioning
        * LDAP/Directory settings configurable via Redfish
        * Security Dashboard - displays the status of important security features, the Overall Security Status for the system, and the current configuration for the Security State and Server Configuration Lock features.
        * Support for Gemalto SafeNet and SafeNet AT key managers
        * InfoSight Optimized AHS Download
        * Show NVMe wear level
        * Workload performance advisor: provides server tuning recommendations to improve server performance


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40
changelog:
  -     The following issues are resolved in this version:
      
        * User interface fixes and improvements
        * Fixed an issue where power supply status changes may be delayed
        * Device Inventory could display a parse error under Internet Explorer 11 when certain PCI Cards are installed
      
      SECURITY FIXES:
      
        * HPESBHF03907
      
      For the latest security bulletins and vulnerabilities, please visit:  
      <https://support.hpe.com/hpesc/public/home>  Security best practices:
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      [http://www.hpe.com/support/ilo5-security-en](http://www.hpe.com/support/ilo5
      -security-enn)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.40-1.1
changelog:
  -     The following issues are resolved in this version:
      
        * User interface fixes and improvements.
        * The text "R&D Server" is incorrectly displayed in the iLO web interface navigation pane.
        * Fixed an issue where power supply status changes may be delayed.
        * Device Inventory could display a parse error under Internet Explorer 11 when certain PCI Cards are installed.
        * Improved shared network port out-of-band LOM resuscitation to reduce the scope and the frequency of system power-on/power-off during systems shutdown/reboot.
        * iLO communication issues in certain configurations where a server is set to Auto-Power-On after an AC power cycle.
      
      SECURITY FIXES:
      
        * HPESBHF03907
      
      For the latest security bulletins and vulnerabilities, please visit:  
      <https://support.hpe.com/hpesc/public/home>  Security best practices:
      
      Please refer to the HPE Integrated Lights-Out 5 Security Technology Brief for
      the latest on security best practices at:  
      [http://www.hpe.com/support/ilo5-security-en](http://www.hpe.com/support/ilo5
      -security-enn)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.43
changelog:
  -     This version adds support for the following features and enhancements:
      
      
      
       \- Added VLAN tagging support on iLO Dedicated NIC for non-blades.
      
      \- Modified the iLO auto-generated SNMP EngineID to not change upon iLO
      resets.
      
       \- Modified Embedded Remote Support (eRS) service events to properly report
      Windows 2019.
      
       \- Reduced the number of Redfish resource change events sent.   Removed
      watching of fields that
      
         change frequently.
      
      \- BIOS Admin password will NOT cause iLO to act as if Require Host
      Authentication is Enabled


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.43
changelog:
  -     The following issues are resolved in this version:
      
      \- Fix for potential firmware use of system memory after free, which could
      lead to an OS exception or
      
         memory corruption under Linux or ESX when using hpilo driver.  It was not
      an issue for Windows.
      
       \- Fix so iLO 5 can connect to switch when both are set to 100 Full Duplex.
      
       \- Fixed REST call so that "ilorest -d serverlogs --selectlog=IML --clearlog
      rc 255" does not fail when
      
         it should succeed.
      
      \- Fixed problem with erroneously logging an IML event for "exceeding power
      capacity threshold" when
      
         it should not be logged.
      
       \- Modified time zone string for "Asia/Taipei" to "Beijing, Chongqing, Hong
      Kong, Urumqi, Taipei, Perth"
      
      \- Only send Remote Support type 1000 events for Critical IML events when they
      should be sent
      
      
      
      SECURITY FIXES:
      
      \- HPESBHF03917
      
        For the latest security bulletins and vulnerabilities addressed in this
      version, please visit:
      
        <https://support.hpe.com/hpesc/public/home>


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.45
changelog:
  -     \- Fixed problem introduced in iLO 5 v1.43 which could cause an HTTP
      connection to be refused under high activity of REST calls.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.46
changelog:
  -     Fixed potential problem of Gen10 Synergy server NIC port being down after
      complete Synergy frame power cycle.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.48-1.1
changelog:
  -      Implemented the set server info command for all the DCi supporting options in previous versions of iLO 5 which may reset NIC settings during iLO 5 update.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10
changelog:
  -     This version adds support for the following features and enhancements:
      
        * Added a security log that lists security events recorded by the iLO firmware.
        * Enhanced Secure Start verification of CPLD on Gen10 Plus servers.
        * Updated menu path and feature names for the Performance Management features. The features that were accessed through the Intelligent System Tuning menu can now be accessed through the Performance menu.
        * Embedded remote support over IPv6.
        * New alert for recovery events.
        * SUM/SUT support on servers using the High Security, FIPS, or CNSA security states.
        * Support for staging firmware to update direct-attached hard drives through the UEFI System Utilities.
        * Ability to import and export drive bay mapping information.
        * Daily firmware flash limit, to protect iLO, ROM, and CPLD from repeated flashing attacks.
        * Performance data logging in a new Active Health System record.
        * Increased the certificate size limit from 4096 to 8096.
        * When iLO is set to the factory default settings, Virtual NIC is enabled by default.
        * The following System Diagnostics features are supported on Gen10 Plus servers: 
          * Booting to safe mode--Allows you to boot the server with a safe minimum configuration.
          * Booting to intelligent diagnostics mode--Allows the system to automatically diagnose a boot failure during POST.
          * Restoring the default manufacturing settings--Resets all BIOS configuration settings to their default manufacturing values. This process deletes all UEFI nonvolatile variables, such as boot configuration, Secure Boot security keys (if Secure Boot is enabled), and configured date and time settings.
          * Restoring the default system settings--Resets all BIOS configuration settings to their default values and restarts the server. This option preserves some UEFI settings.
        * Modified text of iLO time zone selections to match system ROM time zone selections. For backward compatibility, either previous time zone selection text or the new text can be used in APIs to set the time zone.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.10
changelog:
  -     The following issues are resolved in this version:
      
        * The iLO clock incorrectly changes when iLO is reset due to a configuration change, firmware update, or a cause other than system power loss.
        * System GPUs might be listed without GPU version information.
        * Incorrect power consumption information is displayed in RIBCL output and the Active Health System Log.
        * If the domain name system is unavailable, an HPE ProLiant Gen10 Server might stop responding for up to three minutes during startup.
        * Fixed an issue where the iLO 5 webserver may becoming unresponsive when applying OV profile with certain models of NVME drives present.
      
      Security Fixes:
      
        *   For information about the latest security bulletins and vulnerabilities addressed in this version, see the following website: <https://support.hpe.com/hpesc/public/home>.
      
      Security best practices:
      
        *   For the latest information about security best practices, see the HPE Integrated Lights-Out Security Technology Brief at the following website: <http://www.hpe.com/support/ilo-docs>.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.12
changelog:
  -       NVMe drives and open drive support, this includes additional robustness for device discovery and management. This helps to correct some iLO related timeout issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.12
changelog:
  -      The Integrated Remote Console requires code to accommodate low power mode on AMD based system to work with the ROM on EU Lot 9 requirements
        * Incorrect IML messages occur when SAS/SATA drives are installed.
        * Spurious drive hot plug events occur when the server goes through a warm reset
        * In some cases, iLO tries to use an invalid SMBIOS handle from the ROM


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.14
changelog:
  -      Support new Accelerators: 
          * Xilinx Alveo U250
          * Xilinx Alveo U50
        * User can now define pre-caution threshold alert value for the inlet ambient sensor.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.15
changelog:
  -      Users can now restore the last power state after a power outage on Synergy compute modules.
        * Apollo servers now allow you to use the iLO RESTful API to enable or disable power regulation mode (Global settings).
        * Apollo servers now allow you to switch between power regulation modes (iLO Standard license). User Configurable Mode is available only with an iLO Advanced license.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.15
changelog:
  -      Some of the fans in Apollo XL225n Gen10 Plus Servers show a speed greater than 100% in the iLO web interface.
        * The HPE Synergy 3820C 10/20Gb CNA loses flexed sub-ports after a cold boot or E-fuse reset.
        * Updated the thermal parameters for the Xilinx U50 GPU.
        * iLO is temporarily unresponsive or iLO resets on HPE Gen10 servers and HPE Synergy Gen10 compute modules running HPE Infosight.
        * When you query for Software Inventory details, the RESTful Interface Tool 3.0 (part of SUM 8.5.5) does not fetch the "Microchip-smartpqi" driver installed on ESXi7.0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.16
changelog:
  -      Enabled support for Pensando Distributed Services Platform DSC-25 10/25Gb 2-port SFP28 Card.
        * Enabled support for Pensando Distributed Services Platform for HPE iLO Sideband Management Adaptive LOM Module.
        * Added Redfish property for setting the Server to remain Power OFF after thermal shutdown (Critical Temperature threshold exceeded) 
        * Allow Power Regulator Mode management in Apollo platforms without an iLO Advanced license.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.16
changelog:
  -      HPE SimpliVity Accelerator disappear from the thermal sensor data after iLO firmware update.
        * Xilinx U50 cards getting over heat due to wrong thermal limits on iLO 5 v2.15
        * Unable to set HPE m750 Blade Server's Asset Tag through Redfish method.
        * iLO authentication with CM2 credential through Redfish fails frequently with more number of nodes installed.
        * Insight Online shows CPU2 Status as UNKNOWN for HPE ProLiant DL360 Gen10 Servers, while iLO GUI shows CPU2 status as OK.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.19
changelog:
  -      The Direct attached NVMe drives may go missing in the iLO Web Page after random server power cycle.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30
changelog:
  -      MCTP now addresses the iLO false alarm "device/adapter not responsive" issue.
        * Shutdown by virtual button press is included in the iLO enhanced reset cause.
        * Support for initiating the One-button secure erase process from the iLO web interface Lifecycle Management - Decommission page.
        * User account roles provide predefined privilege sets or allow you to define a custom set.
        * New HTML5 remote console modes: Standalone mode and New Window mode.
        * Virtual power button to power NVMe drives on and off. You can access this feature from the Physical Drive Details pane on the Storage Information page.
        * Configuration of Minimum Fan speed using iLO interfaces.
        * Users can view and modify the System thermal configuration settings using iLO interfaces..
        * PLDM firmware update support for NIC and storage option cards.
        * New REST alerts for Auto Heal and Safe Mode.
        * Enabled the iLO webserver to identify the source of request as Host over Virtual NIC.
        * Read support for RDE-enabled devices.
        * Support for flashing Universal FWPKG 2.0 images.
        * Power reading support for Edgeline 8000 systems.
        * Drive Indicator LED - 'Lit' and 'Off' state support for U.2/UBM1/UBM3 with NVMe direct attached storage.
        * When iLO is set to the factory default settings, Virtual NIC is disabled by default.
        * User can now configure iLO to avoid access over an HTTP connection


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30
changelog:
  -      Ripple20 vulnerabilities might affect the TCP/IP stack.
        * Synergy compute modules do not power up after One-button secure erase completes.
        * SPS firmware updates initiated through the iLO Firmware & OS Software pages might fail.
        * C-Class blades do not complete FRU discovery.
        * During central connect Remote Support registration, an error message is not displayed when a  required field is blank.
        * The Virtual NIC feature intermittently fails to provide an IP address to a host with SUSE Linux Enterprise Server 15.
        * Zero Sign In login fails when Kerberos authentication is configured for a large number of groups.
        * When iLO is set to the factory default settings on a fully populated NVDIMM configuration, iLO may lose CHIF communication.
        * DCi compliant Network Adapters under un-managed network configuration, reset to defaults on cold boot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.30-1.1
changelog:
  -     iLO 5 version 2.30(a) was released adding HPE ProLiant m750 server to the
      supported servers. The update does not affect the firmware functionality. If
      version 2.30 was previously deployed to target device, then it is not
      necessary to update to version 2.30(a)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.31
changelog:
  -      Ability to read DIMM serial number using REST API
        * Enabled support for below GPUs: 
          * NVIDIA A100 HGX x4 GPU Air Cooled Baseboard  
          * NVIDIA A100 HGX x8 GPU Air FIO Baseboard  
          * AMD Instinct MI100 PCIE Accelerator


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.31
changelog:
  -      iLO may fail to detect NVMe controllers during power cycle.
        * Firmware version information may not displayed when the server has more than 8 GPUs
        * iLO may reset after FWPKG/PLDM update and coldboot
        * IE and SPS Firmware updates may fail on Gen10 Plus servers 
        * Remote Syslog is made to adhere to RFC 5424 for Unstructured data format    
        * On VSP performing 'cat' or 'head' or 'tail' command on a file that contains some embedded NULL characters hangs the VSP or trims the file after the NULL character
        * Inaccurate Memory Sensor status reported in the vSphere web client for HPE ProLiant Gen10 and Gen10 Plus servers running VMware ESXi 6.5/6.7/7.0 (Refer to [Customer Advisory](https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00106468en_us))


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33
changelog:
  -      Added IPMI lan6 commands support
        * Added ability to view DIMM serial numbers through iLO GUI and redfish API
        * iLO Security logs are now listed in Operating System logs
        * Added ability to change serial Interface configuration using standard redfish schema 
        * Added iLO hostname as part of redfish event header 
        * Enhancement to support Power regulation on AMD servers
        * Power meter data shown in GUI and IPMI CLI has been extended for 1 week
        * Limiting fan speed decrease rate to reduce fan noise. Supported on DL380 Gen10 platform with System ROM U30 v2.40 (10/26/2020) or later
        * Filtering spurious temperature readings for thermal control. Supported on DL380 Gen10 platform with System ROM U30 v2.40 (10/26/2020) or later
        * Enhanced to avoid BMC reset during system POST
        * Option to delete LDAP CA certificate and import CA Certificate of public key larger than 4096 bits (8192 bits, 16352 bits)
        * Banner to be displayed at the SSH login
        * Support enabled for the below controllers on DL385 and DL325 Gen10Plus servers 
          * HPE InfiniBand HDR/Ethernet 200Gb 2-port QSFP56 PCIe4 x16 MCX653106A-HDAT Adapter 
          * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe4 x16 OCP3 MCX653435A-HDAI Adapter
          * HPE InfiniBand HDR/Ethernet 200Gb 2-port QSFP56 PCIe4 x16 OCP3 MCX653436A-HDAI Adapter
        * Enabled support of DCi on Open Adapters
        * Enabled support for below GPUs: 
          * Xilinx Alveo U50 Accelerator 
          * Xilinx Alveo U250 Accelerator 
          * Support enabled for updating the FPGA, CEC Firmware of NVIDIA A100 HGX x8 GPU Air FIO Baseboard through OOB (Out of Band) mechanism
          * Support enabled for disabling write protect for updating GPU, NVSwitch Firmware of NVIDIA A100 HGX x8 GPU Air Cooled Baseboard from host operating system
          * Support enabled for updating the RMI-Remote Management Interface Firmware of AMD Instinct MI100 PCIE Accelerator through OOB (Out of Band) mechanism


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33
changelog:
  -      Error when a user with Read-only role tries to change the password of own account.
        * Resetting iLO to default security state i.e. 'Production' via hponcfg /reset command fails when iLO is in 'High Security' state and 'Require Host Authentication' (RHA) is disabled.
        * Fixed potential security vulnerability CVE-2020-27337 in network stack. Click [here](https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=hpesbhf04070en_us) to know more about the Security Vulnerabilities


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.35
changelog:
  -     Stop pushing AMD APML data to Chassis Controller, only provide data when
      Chassis Controller asks for it
      
      Force Chassis Controller to service iLO I2C request to clear the command queue
      to prevent false communication lock between iLO and Chassis Controller


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.41
changelog:
  -      Added support to import large sized LDAP CA certificate
        * Support enablement for latest Intel Persistence Memory
        * iLO GUI to display the Host Operating System Version
        * Display platform Resiliency and Serviceability (RAS) policy in iLO GUI
        * Added standard redfish schema support for Computer System - Reset, Graceful restart actions 
        * Real CPU temperature is reported in addition to normalized temperature (this feature requires ROM 2.40 version)
        * Support for Active Health System logging by RDE ( Redfish Device Enablement ) enabled devices
        * Support alerting feature for RDE ( Redfish Device Enablement ) enabled devices 
        * Ability to control LED for locating direct attached SATA drives
        * Ability to reset power for direct attached SATA drives 
        * Added write protect setting feature for Liquid cooled Delta/Redstone GPU cards.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.41
changelog:
  -      iLO 5 reporting incorrect Power Supply count with iLO 5 v2.10
        * Continuous logging to IML of a CHIF Error running ESXi with iLO 5 v1.46
        * Random messages "smad[]: No response from iLO for Hello" seen in certain Operating Systems 
        * Incorrect MAC address shown in iLO for Synergy 4820C network adapter
        * InfiniBand card not syncing with Oneview in iLO 5 v2.30
        * Copy/paste may not work for more than 255 characters to VSP terminal in Linux platforms 
        * 547FLR / 1100Q NIC may reset to default mode after flashing from 1.48 to 2.xx


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.44
changelog:
  -     *Critical** : For Synergy servers.
      
      **Recommended** : For ProLiant, Apollo and Edgeline servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.44
changelog:
  -     \- Support for 3rd Gen Intel Xeon Scalable Processors  
      \- Security Hardening enhancements


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.46
changelog:
  -     \- iLO takes more time to update drive details under resource directory in
      redfish in certain situations  
       \- Added A100 40GB/80GB PCIe IDs to GPU support list  
       \- For m750 cartridge installed in a Moonshot chassis: Standard license now
      includes Scripted Virtual Media support  
       \- Redfish "DeviceType" fix to properly label GPU devices that may be hiding
      behind PCIe switch in some Apollo servers


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.48
changelog:
  -     1. Support for 3rd Gen Intel Xeon Scalable Processors
        2. Security Hardening enhancements


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.48
changelog:
  -     1. Fixed the HPE Moonshot standard license issue disallowing Virtual Media. 
        2. Fixed the issue where the Server Platform Service (SPS) firmware was not flashing on the HPE ProLiant m750 Server Blade.
        3. Fixed the issue where the HPE iLO 5 web interface or the HPE iLO Redfish login attempts failed after a 24-hour period on servers installed in an HPE Edgeline EL1000 Converged Edge System or a HPE Edgeline EL4000 Converged Edge System. 
        4. Fixed the issue where plugging in the display port after power on would result in a failure to display video.
        5. Fixed an intermittent issue where some of the NVMe drives were not getting listed correctly in the HPE iLO Redfish and the HPE iLO 5 web interface.
        6. Fixed an issue where the controller was not getting detected when encryption was enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.55
changelog:
  -        Support for HPE ProLiant ML30 Gen10 Plus and HPE ProLiant DL20 Gen10 Plus Server.
        *   Support import of SSL certificate which is more than 20KB via iLO REST and GUI.
        *   Support for PCIE bifurcated slot for Intel E810 2CQDA2 100G NIC.
        *   Support for 64 Character length Password similar to how other vendors provide.
        *   Implemented workaround for health monitoring of NVME M.2 drives as these were partially compliant to NVMe-MI spec.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.55
changelog:
  -      Fixed an issue where the Adapter Virtualization Mode was not persistent across reboots.
        * During System boot/reboot, iLO will stall the complete storage controller discovery such that encryption status query happens after PCIeVDM interface is ready.
        * Fixed an issue where none of the Controller were getting detected when Encryption was Enabled.
        * Fixed intermittent issue where none of the NVME drives were getting detected in OS when iLO is reset multiple times.
        * On XL270d Gen10 Servers, Incorrect capacity of PSU is displayed in iLO Power supplies field after online insertion of HPE 2200W platinum Hot-Plug power supply.
        * Fixed a configuration sync issue during IPv6 initialization when SLAAC Enable/Disable settings were modified.
        * Support added to increase the mapping limit of 32 to 64 physical drives to one logical drive.
        * Fixed the long boot time issue when encryption is enabled on smart array controller.
        * Fixed the NS204i-p unknown status issue after the windows reboot.
        * Fixed the data source for HPE FlexFabric 20Gb 2-port 650FLB Adapter to report correctly when AMS is not installed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60
changelog:
  -        Support for Automatic SSL Certificate Enrollment using Simple Certificate Enrollment Protocol.
        *   Addition of DIMM Manufacture date in RedFISH output of Memory Resource.
        *   Added monitoring of User-defined temperature threshold for PCI Zone sensors on Edgeline servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60
changelog:
  -        OA cannot display FLB (NIC) Info in the GUI as iLO returns an error.
        *   Inconsistent Status displayed for Network Adapter in the GUI.
        *   Improved monitoring of temperature sensors on N3000 option cards.
        *   Fixed an issue where iLO may become inaccessible after consecutive setting of factory defaults.
        *   Improved power supply information reporting on Edgeline servers.
        *   Intelligent Provisioning not accessible after a rare server reboot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60-1.1
changelog:
  -     *Recommended**: For supported HPE Synergy Gen10 and Gen10 Plus systems.
      
      **Optional**:            For supported HPE ProLiant, Edgeline, and Apollo Gen10 and Gen10 Plus systems.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60-1.1
changelog:
  -      Added Support for HPE Synergy Gen 10/Gen10 Plus Systems for addressing the following. 
          * https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=hpesbhf04211en_us
        *   Support for Automatic SSL Certificate Enrollment using Simple Certificate Enrollment Protocol.
        *   Addition of DIMM Manufacture date in RedFISH output of Memory Resource.
        *   Added monitoring of User-defined temperature threshold for PCI Zone sensors on Edgeline servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.60-1.1
changelog:
  -      Fixed an issue where Network Tab page in iLO GUI doesn't refresh automatically post Server Reset.
        * "StructuredName" Redfish Property is hidden when the value of this field is an empty string.
        * Improved monitoring of temperature sensors on N3000 option cards.
        * Fixed an issue where iLO may become inaccessible after consecutive setting of factory defaults.
        * Improved power supply information reporting on Edgeline servers.
        * Intelligent Provisioning not accessible after a rare server reboot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.63
changelog:
  -     *Recommended**: For supported HPE ProLiant, Apollo Gen10 and Gen10 Plus systems.
      
      Is not supported for HPE Edgeline, Synergy Gen10 and Gen10 Plus systems.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.63
changelog:
  -      Support for Cloud based management with Compute Ops Manager (COM).
        * Support for Enhanced Download Performance 
          * This option allows to improve the performance of iLO Scriptable Virtual Media and URL based Firmware update in environments with high network latencies.
        * Support  for NVIDIA A2 PCIE GPU card


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.65
changelog:
  -      Validation of LDAPv3 based authentication using OpenLDAP based directory server.
        * Added Support for RDE Read and Write operations.
        * Added Support for Firmware update using Common PLDM based Package for Direct Attached UBMs (1/2/3/4).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.65
changelog:
  -      Deployment needs to be run twice to reflect Firmware baseline successfully.
        * Change in response of Redfish API causes Oneview not to fully discover the Port Map Information.
        * RF subscription gets exhausted in certain situations.
        * Oneview marks Server as "Critical" when a Critical IML event has been manually marked as repaired in iLO GUI.
        * iLO not able to auto recover when an IML corruption happens.
        * Adapter Virtualization Mode not persistent across reboots.
        * On Edgeline Platforms, iLO GUI doesn't render in the first attempt when IP address is used.
        * iLO webserver becomes unresponsive after running RIBCL scripts for modifying SSO permissions.
        * AMD Gen10 servers might take up to 5 mins to complete POST when encryption is enabled.
        * Nvidia P1000 may not be detected if installed on an EL1000 chassis.
        * Intel N3000 network endpoints are not properly reported on e910t servers.
        * ipmitool lists incorrect number of network port links.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.70
changelog:
  -      Type-D Component Firmware update experience for Compute Ops Management.
        * Support for easy transition to Compute Ops Management for nodes that are currently under OneView management.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.70
changelog:
  -      Port Status of 331i & 562FLR Network Adapter cards do not change from "unknown" to "ok" in rare occasions.
        * "show swid" command displays HPE Smart Array P408i-a SR Gen10 card twice.
        * iLO fails to send Support Events even when Embedded Remote Support has been enabled.
        * iLO responds with wrong Network port information during Ports collection and Network Device Functions collection.
        * Server boot gets stuck on POST while loading Encryption keys for secure boot.
        * EID Table information is retained in AHS though MCTP discovery is disabled.
        * Front Display Port (DP) on Universal Media bay does not work in certain instances.
        * Unable to adjust fan settings on Edgeline e910/e920 Thermal Configuration page.
        * iLO unable to authenticate users intermittently when directory authentication is enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.71
changelog:
  -      UBM6 Backplane Detection Support : New backplane basic support added without firmware update support (Only supported for HPE ProLiant Servers)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72
changelog:
  -      Cannery Row Solution Support.
        * Added support to auto-restore the IPMI and SNMP configuration settings to custom defaults (manually enabled by the user) instead of the factory defaults during abrupt AC power cycle.
        * iLO PLDM Downstream Drive firmware update support enabled.
        * Enhanced the Alerting Mechanism to allow clearing of Events without resetting iLO.
        * PATCH support for Redfish Property "DateTimeLocalOffset"
        * Ability to update Firmware on SATA Drives without Operating System Support.
        * Ability to disable/enable TLS 1.0 and/or TLS 1.1 in Production state.
        * The Temperature page now displays the temperature details of the available PCIe subcomponents.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.72
changelog:
  -      'SessionTimeout' property missing under '/redfish/v1/SessionService' URI
        * GUI reporting configured drives as unconfigured.
        * A router failover post iLO NIC link down and link up could cause iLO to be rendered unreachable over router (default gateway).
        * Incorrect SNMP Trap Data value for cpqSm2CntlrBadLoginAttempts (OID 1.3.6.1.4.1.232.9.2.2.14)
        * Patch operation under redfish URI chassis/1/Thermal not working
        * When a storage controller is configured in Passthrough Mode in ESXi, iLO might take a bit longer to discover Direct Attach NVMe Drive.
        * iLO hostname displays the previous host name after iLO reset.
        * NVMe Backplane Firmware Package 1.0 is not getting updated through iLO.
        * Issue with the JSON payload for Country property
        * Issue with Alertmail IP address reporting on Moonshot systems. 
        * The following weak TLS 1.2 ciphers are disabled in High security state: 
          * 256-bit AES with RSA, ECDH, and a SHA384 MAC (ECDHE-RSA-AES256-SHA384)
          * 256-bit AES with RSA, DH, and a SHA256 MAC (DHE-RSA-AES256-SHA256)
          * 128-bit AES with RSA, ECDH, and a SHA256 MAC (ECDHE-RSA-AES128-SHA256)
          * 128-bit AES with RSA, DH, and a SHA256 MAC (DHE-RSA-AES128-SHA256


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.78
changelog:
  -     Please note iLO 5 v2.78 is positioned to be the bridge version for future iLO
      versions considering that future iLO 5 binary files will be 34 MB in size.
      
      Previous versions of iLO 5 (before 2.78) had provision to only accept iLO 5
      binary which was 32 MB in size.
      
      This restriction has been removed in iLO 5 v2.78. The increase in the bin file
      size will be to support dual payload firmware for ensuring that customers
      
      can use single iLO firmware package on any of the iLO ASICs (T265 or T285).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.78
changelog:
  -      Add support for Intel ATS-M 75W, 100W and 150W
        * Add support for NVIDIA H100
        * Redfish firmware inventory displays CEC FW version (40 GB NVIDIA GPU Drawer)
        * Support for import of a trusted SSL certificate and its corresponding private key.
        * Inclusion of "Context" property in Redfish event which will display the value set by user during Redfish event subscription creation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.78
changelog:
  -      NVMe drive reporting invalid drive IML and illuminating the Amber LED
        * In a configuration with more than 10 logical network controller on bringing the logical controller up or down data doesnt get updated and AMS banner " iLO did not detect Agentless Management"   shows up in iLO GUI.
        * Thermal over temperature alerts observed with respect to Pensando DSP DSC-25 Cards
        * UEFI iLO config utility lets users add special characters to the ILO hostname
        * iLO IP addresses were not included in the SSL certificate SAN even when the user selects this option in the UI
        * iLO is not holding onto Redfish Subscriptions due to invalid Sender-Address in Redfish Event Header
        * For URI /redfish/v1/Managers/@ManagersId/SecurityService/, PATCH on the property TLSVersion  using "Enabled" or "Disabled" fails.
        * On Gen 10 plus AMD systems, with more than 16 PCIe capable SK Hynix drives configured; the behaviour of a single option card (Drives/Storage Controllers/Network Adapters) in the configuration could be unknown or unpredictable.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.81
changelog:
  -      Not clearing error in processing interrupts can lead to interrupt storms leading to firmware watchdog reset 
        * RDE Changes to create Location URI for newly created resource when LRT is completed
        * RDE client MC error code mapping is wrong
        * iLO FW Communication Issue 1) iLO cannot be accessed via Web UI AND/OR 2) Ilorest commands slow/unresponsive post upgrade to iLO version 2.78
        * Server fails to power up as secure start did not complete successfully


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.90
changelog:
  -       Handle Devices reconnection when Bus Device Function information has changed after the Device comes back after Reset. 
        *  Enhancements to ensure Simplified Compute Ops Management onboarding. 
        *  Logging Improvements in Compute Ops Management.
        *  Implemented a flag that allows autoconnection to Compute Ops Management after reboot.
        *  Handle Type - A Firmware Update gracefully even when iLO goes for a reboot. 
        *  Handle Reset scenarios gracefully when updating via Compute Ops Management instead of abruptly going for a reset component gets updated.
        *  Enable/disable SNMP v1 and v3 independently


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.90
changelog:
  -        UEFI iLO config utility lets users add special characters to the ILO hostname
        *   Over Temperature alerts observed with Pensando Cards.
        *   CEC FW Version not seen on iLO 5.
        *   Discrepancy observed in the Current Operating Power comsumption data
        *   Incorrect CPU throttling information observed in iLO.
        *   Incorrect HPE DIMM part number in ERS memory Event.
        *   iLO incorrectly reports missing PSUs and sensor readings.
        *   iLO incorrectly shows connected to Compute Ops Management though connection is not established.
        *   System shuts down when updating Intelligent Provisioning and SPP.
        *   Issues observed on iLO with DL360 Gen10 Server and NVMe SSD Boot drives combination.
        *   Thermal policy is not spinning up fans in some cases resulting in inadequate air flow.
        *   Local User Passwords containing a backslash character may not be set correctly in the iLO 5 Command Line Interface
        *   Organizational Unit attribute is mandatory for the iLO Redfish REST API for generating a CSR whereas in the UI it is marked Optional.
        *   Automatic Certificate Enrollment may not work if the Certificate Authority signing the iLO Certificate Signing Request is an Intermediate.
        *   SPP/SUM Nutanix DX380 (Gen10): Intermittent Issue Updating IE and SPS FW from SPP2022.03.0 - Duplicate of "Intelligent Provisioning and Manageability Engine Firmware fails to get updated intermittently."
        *   "Trap Source Identifier" setting periodically changes to "iLO Hostname" from previously defined "OS Hostname"
        *   IE not updating due to incorrect Target GUID
        *   Caution Threshold and Critical Threshold reported on Memory Temperature sensor of NVIDIA A100-SXM4-80GB


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.91
changelog:
  -     iLO 5 v2.91 has the same content or feature set as iLO 5 v2.90 plus an
      additional fix for COM (Compute Ops Management) related to COM4VC bundle
      update message and event. The additional COM related fix is NOT applicable to
      other regular use case scenarios. Hence upgrading to iLO 5 v2.91 is optional.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.91
changelog:
  -     Fix provided to have synchronous messages to reflect the status, to Compute
      Ops Management, after completion of server reset during bundle update in
      COM4VC use case scenario.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.95
changelog:
  -     \- Added capability in iLO for Two Factor Authentication using OTP (One Time
      Password) for Microsoft AD users  
       \- To display drive enclosure info in Firmware tab in iLO  
       \- Support for controller which goes for functional reset runtime  
       \- iLO to mark the correct component update status for runtime agent
      updatable components based on the update status and update result  
       \- Secure erase of data based on the usecase (customer, factory or openbmc
      ownership transfer)  
       \- iLO stops the bundle update in the scenario where BootToUefi task goes to
      exception to ensure Graceful shutdown of server  
       \- iLO Support for OBSE in factory mode without the need for Advance License  
       \- Added support for comma (",") as a delimiter for multiple email IDs in
      AlertMail feature


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.95
changelog:
  -     \- OEM iLO component does not show the OEM equivalent entry for Intelligent
      Provision in One Time Boot Option  
      \- Handling delayed device discovered in UEFI mode during discovery phase  
      \- Persist the KCS interface setting across iLO reboots  
      \- Capability to enable KCS interface setting without needing a factory reset


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.1
changelog:
  -      This product addressed the disconnection with iLO after switching to Shared Network mode.
        * This product addressed the compatibility of shared memory communication on adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.7
changelog:
  -     This product now supports Red Hat Enterprise Linux 7 Update 4.  
      This product now supports SUSE Linux Enterprise Server 12 SP3.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.7
changelog:
  -     This product corrects an issue where a prompt to save configuration changes is
      displayed when no changes have been made from the adapter's configuration
      menu.  
      This product addresses an issue where an adapter fails to boot to PXE with
      VLAN ID enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.16
changelog:
  -      This product corrects an issue where a user sees a 'Submit Fail for Form:' error message when attempting to load the default (F7) adapter settings.
        * This product corrects an issue where the user is prompted to save changes when no adapter configuration settings have been modified.
        * This product corrects an issue where an adapter's branding information is lost when a non-English language is selected for the 'System Utilities' (F9) menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.11
changelog:
  -     This product corrects an issue where adapters incorrectly send a NULL padded
      System Description LLDP (Link Layer Discovery Protocol) TLV.
      
      This product corrects an issue where an incorrect device (Network Controller)
      name is displayed in the RBSU.
      
      This product corrects an issue where adapters become Firmware corruption
      during rebooting.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.6.4
changelog:
  -     This product addresses an issue where firmware is corrupted during multiple
      system reboots.
      
      This product addresses an LLDP message issue where adapters send incorrect
      System Description, System Name, Chassis ID and Management Address.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.1
changelog:
  -     This product now supports Red Hat Enterprise Linux 7.7
      
      This product now supports  SUSE Linux Enterprise Server 15 SP1
      
      This product now supports the following network adapters.
      
        * HPE Ethernet 10Gb 2-port 537SFP+ Adapter
        * HPE Ethernet 10Gb 2-port 537SFP+ FLR Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.9.3
changelog:
  -      This product corrects wrong names of adapters which show up while doing firmware update.
        * This product corrects an issue about 2 ports in a port bond both being disconnected if we were just disconnecting 1 port.
        * This product corrects an issue about LLDP nearest bridge packet not being disabled while that option under NIC HII was disabled.
        * This product corrects the wrong LED behavior while attaching SFP-RJ45 tranceiver.
        * This product corrects an issue about firmware not being actually updated even seeing it was reported as successfully by update utility.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12.1
changelog:
  -      This product addresses an issue a packet missing problem after some amounts of multicast UDP streams transmitted.
        * This product addresses an issue the port identifier LED problem on HPE Ethernet 10Gb 2-port 535T Adapter .


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.13.0
changelog:
  -     This product no longer supported of updating FW via Service Pack for Proliant
      on HPE Proliant Gen9 servers.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.13.50
changelog:
  -     This product addresses an issue about battery POST error caused by unnecessary
      protocol on Supported Devices of this product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.14.0
changelog:
  -      This product addresses an issue incorrect reporting on link status of HPE 631FLR-SFP28 Adapter.
        * This product addresses an issue battery POST error caused by unnecessary protocol on Supported Devices of this product.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15.2
changelog:
  -      This product enhances bnxtnvm support OTP programming.
        * This product enhances coredump support to dump  cache contents.
        * This product enhances Firmware command line module modularity
        * This product enhances to add support for disabling Overflow detection for CQs (Completion Queues) of RoCE (RDMA over converged Ethernet )
        * This product enhances FW support for QUIC key (Quick UDP Internet Connection) context backing store management
        * This product enhances to add support for PCIe TPH (TLP Processing Hints)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15.2
changelog:
  -      This product correct an issue which not allow the user to configure the multi-function mode option with option value string.
        * This product correct an issue which the performance issue is seen with GRO offload (Generic Receive Offload) enable.
        * This product correct an issue which the Firmware upgrade fails if bnxtnvm uses the default value.  increased the timeout value to sufficient vaule.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.16.2
changelog:
  -      This product enhances the RDE BEJ encoding for some MessageArgs.
        * This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
        * This product removes Energy-Efficient Ethernet (EEE) from the PHY.
        * This product adds range validation checks to dest_port and dest_port_mask for ntuple commands.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.16.2
changelog:
  -      This product fixes the issue of incorrect PCIe VF numbers caused by some NCSI queries.
        * This product fixes the RDE error response for certain properties with unsupported input
        * This product fixes the problem of no RDE alert being generated when the link status changes.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.28.60
changelog:
  -     This product now supports the following network adapters:
      
        * Broadcom BCM5719 Ethernet 1Gb 4-port Base-T Adapter for HPE
        * Broadcom BCM5719 Ethernet 1Gb 4-port Base-T OCP3 Adapter for HPE


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.31.0
changelog:
  -     This product addresses an issue the adjustment of firmware read-write commands
      on corresponding OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.32.3
changelog:
  -     This product correct an issue which the Boot Code Version of the Firmware did
      not get updated after upgrading the Firmware.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33.3
changelog:
  -      This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
        * This product adds to support HPE MicroServer Gen11


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.33.3
changelog:
  -      This product fixes the intermittent issue of displaying incorrect device status under iLO web
        * This product fixes the intermittent lost iLO connection with shared networking mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.1
changelog:
  -      This product addressed a problem where Reboot Required option was not set after doing firmware update under RBSU.
        * This product addressed the disconnection with iLO after switching to Shared Network mode on BCM5719 OCP3 adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.34.50
changelog:
  -     This product addresses an issue where the FAN behavior with installed BCM 5719
      1Gb 4p BASE-T OCP Adptr.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.1
changelog:
  -     *Changes and New Features in version 1.8.1.0.0 :**
      
        * Added hfi1_eprom **v10_8_0_0_13.**
        * Loader ROM **HfiPcieGen3Loader_1.8.1.0.0.rom** and driver EFI **HfiPcieGen3_1.8.1.0.0.efi** were added.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.0
changelog:
  -     *Fixes included in version 1.11.0:**
      
        * **The following issue has been fixed in Unified Extensible Firmware Interafce (UEFI) ROM: **On some platforms, the hfi1 device was not showing up in BIOS/UEFI boot menus and was not available as a PXE boot device. This was caused by the platform not loading the UEFI driver for the hfi1 adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.12.0-2.1
changelog:
  -     *Fixes included in version 1.12.0:**
      
        * Fixed race condition between BIOS checking link status and LNI completing which resulted in PXE boot failures.
        * Changed the default behavior of the hfi1_eprom tool to convert the eprom format to version 2, eliminating the need to supply the -N command line argument.
        * Addressed an issue where updating the HfiPcieGen3Loader*.rom file could result in the erasure of HfiPcieGen3Loader*.efi and HFI_TYPE1*.dat files.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.6
changelog:
  -     This package now supports the HP Ethernet 10Gb 2-port 560SFP+ Adapter.  
        
      This package now supports Red Hat Enterprise Linux 6, Update 3.  
        
      The firmware utility in this package now supports command line options: '-e'
      (rewrite) and '-g' (downgrade).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.3.6
changelog:
  -     This component now supports the following network adapters:
      
        * HP Ethernet 1Gb 4-port 366FLR Adapter
        * HP Ethernet 10Gb 2-port 560FLR-SFP+ Adapter
        * HP Ethernet 10Gb 2-port 560M Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.3.7
changelog:
  -     This component contains new firmware that resolves an intermittent issue where
      the option ROM does not load during POST and the NIC is not available for
      network boot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.4.21
changelog:
  -     This package now supports the following network adapters:
      
        * HP Ethernet 10Gb 2-port 561FLR-T Adapter
        * HP Ethernet 10Gb 2-port 561T Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.17
changelog:
  -     This software now supports the following network adapters:
      
        * HP Ethernet 1Gb 2-port 363i Adapter
        * HP Ethernet 1Gb 1-port 364i Adapter
        * HP Ethernet 1Gb 2-port 367i Adapter
        * HP Ethernet 10Gb 2-port 562i Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.17
changelog:
  -     This firmware addresses an issue where a Pre-Execution Environment (PXE) boot
      fails when the Spanning Tree Protocol is enabled on a network switch.  
        
      This firmware addresses a system hang seen with Product Development Kit Intel
      APITEST with PXE version 1.5.33.  
        
      This firmware addresses an issue where the Windows Deployment Services fail.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.5.19
changelog:
  -     This component addresses an issue which prevented correct operation on the HP
      Ethernet 1Gb 1-port 364i Adapter.  
        
      This component addresses an issue that resulted in sideband communication
      transmitting from the wrong port.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.6.11
changelog:
  -     The nvmupdate tool in this component has been updated to address an issue
      where the shared network port used by Integrated Lights Out (iLO) is not
      correctly enabled on port 1 on the HP Ethernet 10Gb 2-port 560FLR-SFP+
      Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.6.12
changelog:
  -      The firmware flash tool in this component has been updated to address an issue where the shared network port used by Integrated Lights Out (iLO) is not correctly enabled on port 1 on the HP Ethernet 10Gb 2-port 560FLR-SFP+ Adapter.
        * Fixes Wake On Lan issue seen with HP Ethernet 10Gb 2-port 560FLR-SFP+ Adapter.
        * This component addresses an issue described in the Customer Advisory #c04438541.
        * This component contains updated tools that resolve firmware installation issues caused by some EEPROM ID changes.
        * The updated firmware fixes an issue where the PXE boot agent does not load when Intel Boot Agent is set to "Try network first".


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.7.7
changelog:
  -     This product now supports Red Hat Enterprise Linux 6 Update 6.  
        
      This product now supports SUSE LINUX Enterprise Server 12.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.7.7
changelog:
  -     The firmware in this product addresses a Wake-on-LAN (WoL) issue seen with the
      HP Ethernet 10Gb 2-port560FLR-SFP+ Adapter.  
        
      This product addresses the issue described in Customer Advisory #c04438541.  
        
      The firmware in this product addresses an issue where port #1 for an HP
      Ethernet 1Gb 4-port 366FLR Adapter doesn't receive any IP traffic from a
      Dynamic Host Configuration Protocol (DHCP) server.  
        
      This product addresses an issue where firmware update fails on an HP ProLiant
      DL385p Gen8 server.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.15
changelog:
  -     This product now supports the following network adapters:
      
        * HP Ethernet 1Gb 4-port 366T Adapter
        * HP Ethernet 10Gb 2-port 562SFLR-FP+ Adapter
        * HP Ethernet 10Gb 2-port 562SFP+ Adapter
      
      This product now supports Red Hat Enterprise Linux 7 Update 1.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.17
changelog:
  -     This product addresses a link flapping issue seen with the HP Ethernet 10Gb
      2-port 560FLB Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.18
changelog:
  -     This component contains updated tools that resolve firmware installation
      issues caused by some EEPROM ID changes.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.9.12
changelog:
  -     This product now supports Red Hat Enterprise Linux 6 Update 7.
      
      This product now supports SUSE LINUX Enterprise Server 11 SP4.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.10.8
changelog:
  -     This product addresses an issue where the temperature is incorrectly reported
      by the thermal sensors, causing the fans to run high.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.8
changelog:
  -     This product addresses an issue where a firmware update fails when executed on
      a system running Xen.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.12
changelog:
  -     This product addresses an issue where the system may reboot when a firmware
      update is attempted.
      
      This product addresses connectivity issues that may occur while booting
      mounted image when the shared network port is enabled on HPE FlexFabric 10Gb
      2-port 562 FLR-SFP+/SFP adapters.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.13
changelog:
  -     This product fixes link flapping issue reported on the HP Ethernet 10Gb 2-port
      560FLB Adapter.
      
      This product addresses a security issue reported on the following network
      adapters:
      
        * HP Ethernet 10Gb 2-port 562SFLR-FP+ Adapter
        * HP Ethernet 10Gb 2-port 562SFP+ Adapter
        * HPE Ethernet 10Gb 2-port 563i Adapter
      
      See the security bulletin HPSBHF03695 for more information.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.14
changelog:
  -     This firmware corrects an issue where the following network adapters may not
      appear in the system's boot order:
      
        * HPE Ethernet 10Gb 2-port 562FLR-SFP+ Adapter
        * HPE Ethernet 10Gb 2-port 562SFP+ Adapter
        * HPE Ethernet 10Gb 2-port 563i Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.13.12
changelog:
  -     This product now supports Red Hat Enterprise Linux 7 Update 4.  
      This product now supports SUSE Linux Enterprise Server 12 SP3.
      
      This product now supports the following network adapters:
      
        * HPE Ethernet 1Gb 2-port 368i Adapter
        * HPE Ethernet 1Gb 2-port 368FLR-MMT Adapter
        * HPE Ethernet 1Gb 4-port 369i Adapter
        * HPE Ethernet 10Gb 2-port 562FLR-T Adapter
        * HPE Ethernet 10Gb 2-port 562T Adapter
        * HPE Ethernet 10Gb 2-port 568FLR-MMSFP+ Adapter
        * HPE Ethernet 10Gb 2-port 568FLR-MMT Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.14.13
changelog:
  -      This product corrects a Wake-on-LAN (WoL) issue seen with the HP Ethernet 1Gb 2-port 361T Adapter.
        * This product corrects an issue where there is no VLAN function under Legacy mode on the HP Ethernet 1Gb 2-port 361T Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.14.14
changelog:
  -     This product addresses an issue where link flapping is seen when the 'HP
      Ethernet 10Gb 2-port 560FLB Adapter' is connected to 1Gb interfaces and
      operated at 1Gb speeds.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.15.9
changelog:
  -     This product addresses a NIC VLAN ID issue seen in the NIC Human Interface
      Infrastructure (HII) menu when operating in UEFI mode.  
      This product addresses a teaming issue where the HPE Ethernet 10Gb 2-port 561T
      Adapter still shows connected on the switch after the NIC has been disabled.  
      This product addresses a link issue and a PXE issue seen with the HPE Ethernet
      10Gb 2-port 560FLB Adapter.  
      This product addresses a WOL issue seen with the HPE Ethernet 1Gb 4-port 366T
      Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.17.17-2.1
changelog:
  -     This product addresses a failure to update adapter firmware on a system
      running SUSE Linux Enterprise Server 15.  
      This product corrects an issue where the name for the HP Ethernet 1Gb 4-port
      366FLR Adapter is displayed incorrectly in the network boot options.  
      This product corrects an issue where the HPE Ethernet 10Gb 2-port 562FLR-T
      Adapter can be awakened when the NIC WOL setting is disabled.  
      This product corrects an issue where system hangs when booting from the PXE
      boot menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.17.19
changelog:
  -     The firmware in this product addresses an issue where the "Shared Memory
      Feature" would be set to Enabled after Firmware upgrade with HPE Ethernet 10Gb
      2-port 561T and 561FLR-T Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.18.7
changelog:
  -     This product addresses an issue where shared memory settings are not preserved
      after a firmware update.
      
      This product addresses an issue where the Legacy VLAN ID isn't reset to 0
      while pressing F7 to reset to default.
      
      This product addresses an issue where, after a firmware update for the HPE
      Synergy 4610C 10/25Gb Ethernet Adapter, the server fails to power up due to
      thermal fault errors.
      
      This product addresses an issue where firmware update for all Intel adapters
      fails when the system contains an obsolete Intel adapter.
      
      This product addresses an issue where the MAC of the HPE Ethernet 10Gb 2-port
      562T Adapter is duplicated after applying the 09.2018 SPP.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.18.10
changelog:
  -     This product corrects an issue where the default value of Legacy Noot Protocol
      isn't set to PXE with HP Ethernet 1Gb 4-port 366FLR Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.19.11
changelog:
  -     This product now remove supports Synergy and Blade Server.
      
      This product now supports Red Hat Enterprise Linux 8.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.19.11
changelog:
  -     This product addresses an issue where LLDP are disabled.  
      This product addresses an issue where "Firmware Image Properties", "Device
      Level Configuration", and "Link Speed Status" options in NIC HII menu will
      disappear when F7 is pressed.  
      This product addresses an issue where Firmware upgrade fail in SLES15 with
      secureboot enabled.  
      This product addresses an issue where POST when ESC Is Pressed to Enter The
      BIOS Setup Utility with HP Ethernet 1Gb 4-port 366FLR Adapter.  
      This product addresses an issue where there is no VLAN function under Legacy
      mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.19.11-2.1
changelog:
  -      This product now supports Red Hat Enterprise Linux 6. 
        * This product now supports Red Hat Enterprise Linux 8. 
        * This product no longer supports ProLiant Blade servers and devices. Those servers and devices are now supported by the [HPE Blade Intel Online Firmware Upgrade Utility for Linux](https://www.hpe.com/global/swpublishing/MTX-f35e20f5c7624892a850ceb642).
        * This product no longer supports Synergy servers and devices. Those servers and devices are now supported by the [HPE Synergy Intel Online Firmware Upgrade Utility for Linux](https://www.hpe.com/global/swpublishing/MTX-bde50c38fbba4c2cb39d29468b).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.19.11-2.1
changelog:
  -      This product addresses an issue where LLDP are disabled.
        * This product addresses an issue where "Firmware Image Properties", "Device Level Configuration", and "Link Speed Status" options in NIC HII menu will disappear when F7 is pressed.
        * This product addresses an issue where Firmware upgrade fail in SLES15 with secureboot enabled.
        * This product addresses an issue where POST when ESC Is Pressed to Enter The BIOS Setup Utility with HP Ethernet 1Gb 4-port 366FLR Adapter.
        * This product addresses an issue where there is no VLAN function under Legacy mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.19.30
changelog:
  -     This product addresses an WOL issue that system wakes up automatically if any
      magic packet being sent before system was shut down.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20.10
changelog:
  -     This product addresses an issue where ECC error occurs when running failed
      recovery with HPE Ethernet 10Gb 2-port 562T Adapter and HPE Ethernet 10Gb
      2-port 562FLR-T Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20.37
changelog:
  -     This product addresses a FW update issue that fails to update FW with this
      specific NIC FW version (80001FB7/1.2529.0).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.21.6
changelog:
  -     This product addresses an issue where Systems Insight Display (SID) modul is
      green when there's no Network connection.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.6
changelog:
  -     This product now supports Red Hat Enterprise Linux 8 update 4 and SUSE Linux
      Enterprise Server 15 Service Pack 3


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.50
changelog:
  -      This product addresses an issue where link flipping is seen with HPE Ethernet 10Gb 2-port 568FLR-MMSFP+ Adapter.
        * This product addresses an issue where the link speed isn't consistent with HPE Ethernet 10Gb 2-port 568FLR-MMT Adapter when system shutdown.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.0
changelog:
  -      This product addresses an issue where SR-IOV high latency is seen with HPE Ethernet 10Gb 2-port 562SFP+ Adapter and HPE Ethernet 10Gb 2-port 562FLR-SFP+ Adapter.
        * This product addresses an issue where it fails to disable HP Ethernet 1Gb 2-port 361i Adapter in RBSU.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.35
changelog:
  -     This product addresses a issue where IGMP2 packets isn't forwarded to the host
      OS when shared NIC is enabled with HPE Ethernet 1Gb 2-port 361i Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.27.0
changelog:
  -      This product addresses an issue where Option ROM version is missing with some Intel 1GB adapters
        * This product addresses an issue where disconnection occurs after rebooting system with HPE Ethernet 1Gb 2-port 368i Adapter and HPE Ethernet 1Gb 4-port 369i Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.27.30
changelog:
  -     This product addresses an issue where NIC status(iLO page->System
      Information->Network) for HPE Ethernet 10Gb 2-port 562SFP+/562FLR-SFP+ Adapter
      is Unknown with being plugged in to a network.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.28.0
changelog:
  -     This product addresses an issue where the firmware installation exceeds the
      expected time by using Oneview to update Firmware with 568FLR-MMSFP+.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.20.11
changelog:
  -      This product now supports SUSE Linux Enterprise Server 12 SP5.
        * This product now supports HPE ProLiant MicroServer Gen10 Plus and HPE ProLiant XL225n Gen10 Plus.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.21.5
changelog:
  -     This product now supports the following network adapters:
      
        * Intel X710-DA2 Ethernet 10Gb 2-port SFP+ OCP3 Adapter for HPE
        * Intel X710-DA2 Ethernet 10Gb 2-port SFP+ Adapter for HPE


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.11
changelog:
  -      This product now supports SUSE Linux Enterprise Server 15 SP2.
        * This product now supports Red Hat Enterprise Linux 8, Update 2 and Update 3.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.55
changelog:
  -     This product addresses an link issue for Intel X710-DA2 Ethernet 10Gb 2-port
      SFP+ OCP3 Adapter for HPE.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.23.50
changelog:
  -      This product addresses an issue where the incorrect translation is seen with Intel Intel I350-T4 Ethernet 1Gb 4-port BASE-T  Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.25.4
changelog:
  -     This product addresses an issue where the adaters isn't recongized with HPE
      Ethernet 10Gb 2-port SFP+ OCP3 X710-DA2  Adapter and HPE Ethernet 10Gb 2-port
      SFP+ X710-DA2 Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0
changelog:
  -     *Firmware for the following device is updated to 14.24.9000 :**
      
      P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **Changes and New features in firmware version 14.24.9000 :**
      
        * Changed the firmware version string format in the HII from xx.yy.vv.zz to xx.yy.zzzz.
        * Enabled Firmware Management protocol installation on the Controller handle instead of the child handle.
        * The MTU value is set to 1500 upon driver bring up.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0
changelog:
  -     *Fixes in version** **14.24.9000**
      
        * Fixed an issue that prevented the first iSCSI target parameters to be reset to their default values.
        * Fixed an issue which cause the link not to raise in the second port which was set as IB when the first port was ETH in PXE.
        * Fixed wrong default value of Boot-To-Target in FlexBoot configuration.
        * When connecting a pre-configured port with VLAN to an IB fabric, the port runs as Ethernet port with the VLAN tag.
        * Booting PXE using Grub2.X over HP G9/G8 servers results in system hang.
        * If the client gets "PXE boot menu" when contacting the DHCP, it will PXE boot first regardless of the boot priority.
        * If the PMM fails to allocate memory, the system hangs since FlexBoot cannot load from the expansion ROM.
        * In ConnectX-4, the PXE boot time measurement over TFTP Ethernet was 1:30 min for image size of 1GB, TFTP InfiniBand was 1:20 min, and iSCSI boot time measurement was 8 seconds for image size of 25 MB.
        * In hybrid BIOSes, if the BIOS loads legacy driver without closing the UEFI driver, the legacy driver fails to load.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Firmware for the following device is updated to 14.26.1040:**
      
      P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Fixes in version** **14.26.XXXX :**
      
        * Fixed an issue that caused a function to misbehave when a PCIe Transaction Layer Packet (TLP) was set with a poisoned indication.
        * Fixed a rare issue that resulted in "destroy mkey " command getting stuck when rebooting the hypervisor.
        * The total firmware reset time is increased by 1 second.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Firmware for the following device is updated to 14.27.4000:**
      
      P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **Following New features and Changes are included in version 14.27.4000:**
      
        * Added mlxconfig support for power reduction: PCI CAP AUTO_POWER_SAVE_LINK_DOWN 
          * PCI CAP
          * AUTO_POWER_SAVE_LINK_DOWN
        * Added the following segments, as appeared in the PRM, to the Resource Dump: 
          * PRM_QUERY_QP
          * PRM_QUERY_CQ
          * PRM_QUERY_MKEY
          * QUERY_VNIC_ENV


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Following issues have been fixed in version 14.27.4000:**
      
        * An issue that caused the sent packet to hang while the device entered FLR mode.
        * Enabled Bar configuration bytewise by applying the write_en bitmask.
        * A rare case where the the device froze while running the sw reset flow under heavy stress and with many open resources.
        * Low PXE performance while using the VSC to trigger the send_ring_doorbells.
        * An error that prevented the completions (CQ) from being completed due to a race condition in the firmware transport error handlers, and the error stressors, where the error stressors would hang the firmware transport error handler flow.
        * An issue that caused the fragmented IP packets to drop was fixed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Firmware for the following device is updated to 14.28.1002:**
      
      P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **Following New features and Changes are included in version 14.28.1002:**
      
        * Added mlxconfig support for power reduction: PCI CAP AUTO_POWER_SAVE_LINK_DOWN 
          * PCI CAP
          * AUTO_POWER_SAVE_LINK_DOWN
        * Added the following segments, as appeared in the PRM, to the Resource Dump: 
          * PRM_QUERY_QP
          * PRM_QUERY_CQ
          * PRM_QUERY_MKEY
          * QUERY_VNIC_ENV


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Following issues have been fixed in version 14.29.1016:**
      
        * An issue that caused the sent packet to hang while the device entered FLR mode.
        * Enabled Bar configuration bytewise by applying the write_en bitmask.
        * A rare case where the the device froze while running the sw reset flow under heavy stress and with many open resources.
        * Low PXE performance while using the VSC to trigger the send_ring_doorbells.
        * An error that prevented the completions (CQ) from being completed due to a race condition in the firmware transport error handlers, and the error stressors, where the error stressors would hang the firmware transport error handler flow.
        * An issue that caused the fragmented IP packets to drop was fixed.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Firmware for the following device is updated to 14.31.1014:**
      
        * P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **New features and changes included in version 14.31.1014:**
      
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Following issues have been fixed in version 14.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1014:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following device has been updated to 14.32.1010:**
      
        * P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6-2.1
changelog:
  -     *The following changes have been made in sub-version 1.0.6(A):**
      
        * Product rebuilt to have the new SHA 384 signature.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.32.5430:**  
        
      779799-B21  
      779793-B21


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0-2.1
changelog:
  -     Fixes in v2.32.5430:
      
        * Fixed an issue causing ARP not to reply when connected to Hyper-V vSwitch.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Firmware for the following devices are updated to 2.33.5220:**  
        
      779799-B21  
      779793-B21


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Firmware for the following devices are updated to 2.34.1300:**  
        
      779799-B21  
      779793-B21


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Fixes in 2.34.5010**:
      
        * Fixed OCBB Section5 event 8 FEATFLAG
        * Fixed wrong host visible firmware string report when running the HP "OEM GET HOST PARAMETER" command.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Firmware for the following devices are updated to 2.35.5100:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Fixes in 2.35.5100:**
      
        * Fixed OCBB Section5 event 8 FEATFLAG
        * Fixed wrong host visible firmware string report when running the HPE "OEM GET HOST PARAMETER" command.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.36.5000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.36.5000:**
      
        * Enables steering packets to receive queues according to Ethertype matching (See PRM 2.1 for more information).
        * Adds support for additional rate values.
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
      
      **Firmware for the following devices are updated to 14.14.2200:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Fixes in 2.36.5000:**
      
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed an issue which caused a firmware internal error when handling QP alternative context.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected.
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
      
      **Fixes in 14.14.2200:**
      
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-3.1
changelog:
  -     *Firmware for the following devices are updated to 2.36.5000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.36.5000:**
      
        * Enables steering packets to receive queues according to Ethertype matching (See PRM 2.1 for more information).
        * Adds support for additional rate values.
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
      
      **Firmware for the following devices are updated to 14.14.2204:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **New features and changes in version 14.14.2204:**
      
        * Reduced the OCBB frequency update rate.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-3.1
changelog:
  -     *Fixes in 2.36.5000:**
      
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed an issue which caused a firmware internal error when handling QP alternative context.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected.
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
      
      **Fixes in 14.14.2204:**
      
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.40.5030:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.40.5030:**
      
        * Added Etherent Link down counter.
        * Enables steering packets to receive queues according to Ethertype matching 
        * Adds support for additional rate values. 
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
        * New performance and back-pressure counters command via PRM (For further information, please refer to the PRM)
        * Support for Multicast/Unicast sniffer rules (For further information, please refer to the PRM)
        * Support for VLAN in VLAN encapsulation (For further information, please refer to the PRM)
        * CQ creation offload by software
        * Support for rst2rts command
        * Invalidates a TLV during the firmware boot stage
        * A new counter for the diag_rprt PRM command to count packet drops due to noreceive buffer
        * Support for Ethernet TX lifetime cycle control (Head of Queue)
        * A new register (PPLR) that allows egress and external loopback control (For further information, please refer to the PRM)
        * A watchdog mechanism to track ingress traffic stalls to prevent flooding the network with Flow Control packets
        * Inspur LED scheme: A new LED scheme controlled by the INI which causes constant traffic LED indication even without traffic.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Sideband moved to port 0
        * Added MCTP command support
        * Changed the HP LED scheme for the 779799-B21 adapter.
      
      **Firmware for the following devices are updated to 14.18.2030****:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
        * Added logical link indication in SFP to BaseT modules and disabled logical link when peer port is down.
        * Added support for 10GbE in 25GbE SFP optical modules.
        * Enables mlxlink tool to collect data on the PHY link status and provides link down reasons and additional link related information.
        * Enabled TX configuration response and movement during Link Training in Ethernet.
        * Added support at lane rate of 12.89Gb.
        * Limits the amount of time a packet may head a Traffic Class (TC) transmission queue, without being transmitted. Stale packets are discarded. Active by default for TCs adhering to link level flow control.
        * UAR page size currently is set to 4KB and not according to what the system page size determines.
        * Improved performance of:  
       Doorbell from User Access Region (UAR)  
       Clear interrupt from User Access Region (UAR)
      
        * Added support for additional transport counters.
        * Added ODP support for DC.
        * Enabled scatter-to-CQE for sent packets for DC.
        * Enabled moderation period modification in CQ modify command.
        * Added support for minimum/maximum rate limit per vport in SR-IOV.
        * Enabled network traffic between UEFI-Shell and OS.
        * Enabled the PF to force disable RoCE for its VFs.
        * Added 2 new access registers:  
       Management Capabilities Mask Register  
       Ports CApabilities Mask Register Fields  
      For further information, please refer to the PRM.
      
        * Enabled VNIC the control to enable/disable its local loopback traffic.
        * Added the option to open a receive RDMA Flow Table and to forward RoCE traffic to some destination QP.
        * Added support for Multi-Host LID base routing. This feature requires a new OpenSM (v4.7.1 and above which comes with MLNX_OFED 3.3-2.0.0.0) with the following attributes:  
       qos TRUE  
       lmc 2 (if there is no quad host in the fabric, you can set the lmc to 1)  
       virt_enabled 2 Note: Multi-Host LID base routing can be configured by the
      INI only. The default is 0
      
        * Resilient RoCE is the ability to send RoCE traffic over a lossy network (a network without flow control enabled), without the need to enable flow control on the network. The ability is accomplished by enabling ECN on both the Switch and the Host.
        * Enables load balancing in the Multi PF Switch layer (MPFS) based on the L3/L4 headers
        * Increased the number of VFs from 64 to 95 per Physical Function (PF). Note: When increasing the number of VFs, the following limitations must be taken into consideration: server_total_bar_size >= (num_pfs)*(2log_pf_uar_bar_- size + 2log_vf_uar_bar_size*total_vfs) server_total_msix >= (num_pfs)*(num_pf_msix + num_vfs_msix *total_vfs) Note: For the maximum number of VFs supported by your driver, please refer to your drivers' Release Notes or User Manual.
        * Added support for Port Flap Counter.
        * Limits the buffer size for all entries to improve performance. KSM is used when associating Key Length My Virtual Address (KLMs) with fixed memory size.
        * This entry (null_mkey) is use to indicate non-present KLM/KSM entries. When accessing is, it causes the device to generate page fault event.
        * PLDM firmware burning is based on the DMTF spec DSP0267 (draft 9). The feature enables upgrading firmware and expansion ROM images using the PLDM protocol over MCTP (over PCIe). By doing so, a supporting BMC can query and upgrade the firmware without using OS based tools.
        * Added a new physical layer statistics counters group. The new group includes BER counters, FEC error correction, clear time, and additional physical layer counters. For further information, please refer to the Ethernet Adapters Programming Manual (PRM).
        * Enables the user to set a certain link up state for an unlimited period of time. This mode has 3 states:  
       Aux power (standby)  
       Reboot/boot/driver unloaded - the server is active and no driver is up  
       Driver is up - at least one driver is up (the time between init HCA and
      teardown or FLR)
      
        * Added support for Doorbell from User Access Region (UAR).
        * [Beta] Added support for maximum rate limit per function in SR-IOV.
        * Allows the user to configure the adapter card to stop sending pauses after x when the receive port is unavailable (in a hang state).
        * [Beta] Added support for new performance counters.
        * DCBX is used by DCB devices to exchange configuration information with directly connected peers. DCBX uses Link Layer Discovery Protocol (LLDP) to exchange parameters between two link peers. For further information, please refer to the PRM.
        * Allows network port registers to revert to their default values when the driver is restarted or the host is rebooted.
        * Added additional network link up modes. The new modes decide when to keep the network link up. The new modes are:  
       keep_eth_link_up  
       keep_ib_link_up  
       keep_link_up_on_boot  
       keep_link_up_on_standby
      
        * Added v1, v3, v6 tags to VPD read only tag
        * Enables software to scatter or strip FCS in RQ.
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time. 
        * Applies pause functionality to specific classes of traffic on the Ethernet link.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors
        * The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB.
        * ConnectX-4 adapters now support 1Gb/s and 56GbE Ethernet connectivity in addition to 10GigE, 25GigE, 40GigE, 50GigE, and 100GigE.
        * Provides a clear indication of Flow Steering statistics and errors.
        * The minimal amount of packet headers inlined in the WQE's Eth Segment.
        * A flow table may include a table-miss flow entry, which renders all Match Fields wildcards. If a packet does not match a flow entry in a flow table, this is a table miss. The behavior on a table miss depends on the table configuration. A table-miss flow entry in the flow table may specify how to process unmatched packets.
        * Single Root IO Virtualization (SR-IOV) is a technology that allows a physical PCIe device to present itself multiple times through the PCIe bus.
        * Uses the HCA for offloading erasure coding calculations.
        * Enables the administrator to add a timestamp to the firmware they want to upgrade to avoid situations where one host tries to upgrade the firmware and another tries to downgrade; which may lead to two or more unnecessary server reboots. For further information, please refer to MFT User Manual.
        * The change includes the following:  
      1\. Changed port configuration which required link re-training (such as speed)  
      2\. PAOS down  
      3\. PAOS up  
      This change, will cause the link to toggle and new configurations to take
      effect.
      
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image. For further information, please refer to MFT User Manual.
        * Improved TX signal integrity for Electromagnetic Induction (EMI) compliance.
        * Optic modules thermal sensing - Enables the firmware to read and report the temperature of the module.
        * PLDM for module thermal sensing - Supports platform-level data models and platform functions in a platform management subsystem. PLDM is designed to be an effective interface and data model that provides efficient access to low-level platform inventory, monitoring, control, event, and data/parameters transfer functions.
        * Low power boot state - Enables u-boot to put non-boot CPUs into a low power status. To enable low power boot using iLO debugger use the following commands.  
                            * Port shutdown due to optic thermal event - Enables the firmware to close the power cage in case of high temperature in the module.
        * Reduced the port link-up time when negotiating according to Clause 73 (DME)
        * Large Receive Offload (LRO)  Large Send Offload (LSO)
        * Receive Side Scaling (RSS)
        * Global Pause  RoCEv1.0/RoCEv2.0
        * Flow Steering
        * Sniffer Ethernet
        * Rate Limiter (at Beta level)
        * Multi packet WQE
        * Enhanced Transmission Selection standard (ETS)
        * Explicit Congestion Notification (ECN)
        * Priority Flow Control (PFC)
        * CQE time stamping
        * PCIe Function Level Reset (FLR)
        * Power Management L2/L3 flow support
        * Strided SRQ
        * Self Loopback support
        * Transport Domain support
        * CQ2EQ remapping
        * Added support for the following commands:  
       MODIFY/QUERY_ESW_VPORT_CONTEXT  
       QUERY/MODIFY_CONG_STATUS  
       QUERY/MODIFY_CkONG_PARAMS  
       QUERY_CONG_STATISTICS  
       ADD/DELETE_VXLAN_UDP_DPORT


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-2.1
changelog:
  -     *Fixes in 2.40.5030:**
      
        * Fixed a race between the firmware and the hardware during driver start which blocked outbound completions.
        * Fixed an issue which caused the firmware not to send link_down event to the driver when running the close_port command.
        * Fixed an issue where in rare cases the Auto Sense failed to detect the right protocol.
        * Fixed signal integrity issue when connecting a WCS ConnectX4 mezz card to Pikes peak FPGA..
        * Added the option to transmit corrupted DME pages for a very short period of time at the beginning of the Auto-Negotiation flow.
        * Fixed an incorrect report of the PortRcvDataVLExtended / PortXmitDataVLExtended counters by the firmware.
        * Fixed a rare issue which caused firmware's packet injector to cut off packets when the TX was congested.
        * Fixed an issue that caused the response to TX requests to take up to 10 mili-seconds in IEEE clause 72 Link Training.
        * Fixed a race between 2 iriscs which caused a QP to get stuck in burst control limit state.
        * When a QP was in error state, the firmware generated too many err CQEs at once, thus causing the cmdif responsiveness to be too slow. To prevent the above, the number of err CQEs was limited to 16 at a time.
        * Fixed an issue that caused the MAC address that was set from the OS using ifconfig to be not reflected in the OCBB buffer.
        * Fixed an issue where the ibdump got broken when running with loopback traffic.
        * Fixed an issue where the firmware took QP to firmware ownership and then released it to the hardware ownership without checking if another firmware flow owns the same QP.
        * Fixed an issue which occurred after disconnecting cable which showed the link type as IB even if the link type of the port is ETH.
        * Fixed an issue related to the HCA PoerXmitWait counter on port 2 (connected to port 2 on Switch-IB) where it started counting and reached 0xFF's regardless of connection to switch.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping. 
        * Fixed an issue which caused a firmware internal error when handling QP alternative context. 
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed a wrong reporting of section 5 event 8 - LSO support.
        * Fixed a mistakenly dropped ETH packet with ethertype 0x600 by the NIC.
        * Fixed a case preventing broadcast traffic from arriving to their destination after detaching high priority broadcast rule on a port where NC-SI was enabled.
        * Fixed an issue where the port raised as SDR vs. InfiniScale IV QDR Switch
        * Fixed a rare case of completion Error with Bad Opcode sequence status which occurred when retransmitting read requests
        * Fixed a case where the actual bandwidth did not match the user settings in VM QoS.
        * Fixed a case where on rare cases, communication to BMC was lost during driver initialization.
        * Fixed an issue with cable reading, which caused the link not to raise.
        * Set the maximum EQN number to 1024.
        * Fixed a rare issue with VPD init flow which caused read failures.
        * Fixed an issue with RX size counter not being reported.
        * Fixed promiscuous mode compatibility with A0-DMFS steering.
        * Fixed promiscuous mode compatibility when NC-SI is enabled and configured.
        * Fixed sending/receiving OEM temp commands (set/get) with channel ID 0x1f failure.
        * Fixed an issue which caused packets to drop on a port when changing the interface state of the other port.
        * Fixed long management communication loss and SOL hang during reboot cycles.
        * Fixed wrong processing of inbound traffic towards BMC which caused communication loss.
        * Fixed management link loss upon closing port interface through the driver.
        * Fixed a false indication in firmware of an expander presence causing delay in EEPROM reading.
        * Fixed an issue which caused a link down on a port when the cable was removed from the other port.
        * Fixed a rare case where packet with length zero got stuck in hardware queues.
        * Fixed an issue which caused InfiniBand congestion control packet (CNP) to hang in hardware.
        * Fixed an issue which caused AEN to be sent after channel reset.
        * Fixed an issue which prevented the restoring of QoS setting to its default consequently causing bandwidth degradation.
        * Fixed an occasional long link up time with 10GbE based devices.
        * Fixed an issue preventing cable readings from i2c slave address 0x51
        * Fixed a wrong parity bit calculation when transmitting PCIe TS1 packets.
        * Fixed a possible deadlock in PM turnoff request transmission and ack acceptance flow.
        * Fixed a rare case with alignments state machines which caused occasional width degradation.
        * Fixed an issue where the transmit queues hanged while congestion control was enabled and operational (EQC/QCN)
        * Fixed an unexpected work completion syndrome with vendor syndrome 0x77 received when running RDMA SEN/WRITE traffic with retransmissions.
        * Fixed an issue which caused SetPortInfo to return a good status when receiving invalid LinkSpeedEnabled value.
        * Fixed an issue which caused dual port SFPP module cards to be automatically mapped with expander.
        * Fixed an issue where firmware overrides the steering mode that was chosen by the driver.
        * Fixed invalid return sensing results occurred when the link was up.
        * Fixed an issue causing the sensing result to be delayed when cable was unplugged.
        * Fixed an issue causing the link type to be displayed as ETH when set to AUTO.
        * Fixed an issue causing ARP not to reply when connected to Hyper-V vSwitch.
      
      **Fixes in 14.18.2030****:**
      
        * On rare occasions during UEFI boot cycles system got stuck while WinPE is loaded. (OS WinPE, system DL160).
        * Single FTE that catches both untagged and prio-tagged packets (by giving an FTE with match_value.vlan_tag = 0 and match_value.vid = 0) is currently not supported.
        * Flashing the firmware requires server reboot. Firmware cannot be flashed twice without server reboot after first flashing
        * If the vport state is DOWN and a packet is sent in local loopback, the sx_sniffer tool will not function.
        * Fixed an issue causing bubbles to appear as symbol errors when link raised FDR 1x.
        * When Clause 74 Fire-Code FEC is active, and there are FC corrected errors, both the FC_correctable counter and the FC_uncoreectable counter are increment.
        * Some Port Control Register do not return to the default value after the last port owner host restarts the driver.
        * Fixed an issue which caused RX to hang when the UDP packet had a reserved UDP destination port.
        * Fixed DMAC reporting mapping per host.
        * Fixed an EEH error from PCI which caused firmware to hang.
        * Fixed the default value of the PCIe target_link_speed to Gen3 in link control2.
        * Fixed an issue which prevented LEDs from blinking when the traffic was less than 0.1% of the link speed.
        * Fixed an issue which caused the mlxconfig configuration of VF_LOG_BAR_SIZE to be ignored and to be set to 5 (32MB).
        * A server getting into a Standby mode while Packet-Pacing is enabled might cause firmware to hang and driver call-trace.
        * Fixed an issue which caused unexpected QoS functionality in case of multiple sources to single destination traffic transmission.
        * Fixed an issue which occasionally caused the RX traffic to hang in DC when received a PCI error on WQE fetch.
        * Fixed OOB connection issue during Intel's ITP inject errors test.
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.
        * Fixed a UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GbE OCP card.
        * Fixed an issue which prevented Vport counters from counting local loopback packets. Packets now are filter by the self-loopback prevention.
        * Reported INTx as unsupported to allow PFs Passthrough on PowerKVM.
        * SR-IOV Ethernet supports up to 18 VFs per port only.
        * Fixed and incident what allowed local (internal) loopbacked packets to be counted by the Vport counters, although Vport counters should count only traffic that crosses the Vport.
        * Fixed an issue preventing driver loading or TX traffic sending upon reboot, after ungraceful driver unload.
        * Fixed casting of BMC MAC before steering API.
        * Fixed the PCI write flow to take into consideration the PCI MTU. This fix eliminates the need for NOPs in the flow, which resulted from PPC larger PCI MTU.  
      The single queue limitation for READ is due to a hardware limitation of the
      number of READ request in a given time.
      
        * Fixed a case that caused FlexBoot to not work as expected with systems that run with "large bar" enabled (Above 4G Decoding) over Connect-IB or ConnectX-4 HCAs.
        * Fixed an issue which prevented link creation when connected to IXIA 25G.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-4.1
changelog:
  -     *Firmware for the following devices are updated to 2.40.7000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.40.7000:**
      
        * Added Etherent Link down counter.
        * Enables steering packets to receive queues according to Ethertype matching 
        * Adds support for additional rate values. 
        * Counters that count the number of repeated Send WQE cache lookups that resulted in a miss.
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image.
        * New performance and back-pressure counters command via PRM (For further information, please refer to the PRM)
        * Support for Multicast/Unicast sniffer rules (For further information, please refer to the PRM)
        * Support for VLAN in VLAN encapsulation (For further information, please refer to the PRM)
        * CQ creation offload by software
        * Support for rst2rts command
        * Invalidates a TLV during the firmware boot stage
        * A new counter for the diag_rprt PRM command to count packet drops due to noreceive buffer
        * Support for Ethernet TX lifetime cycle control (Head of Queue)
        * A new register (PPLR) that allows egress and external loopback control (For further information, please refer to the PRM)
        * A watchdog mechanism to track ingress traffic stalls to prevent flooding the network with Flow Control packets
        * Inspur LED scheme: A new LED scheme controlled by the INI which causes constant traffic LED indication even without traffic.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Added support for multiple RoCE modes (RoCE v1+v2) on the same port: RoCE mode is per connection now.
        * Added a new QP command "INIT2RTS_QP" to enhance QP connection readiness time.
        * Disabled FCS checks to support switches that replace FCS with Timestamp.
        * Added RX Port identification for direct rout packets.
        * Improved RDMA WRITE/SEND performance with retransmissions.
        * Enabled firmware burning/querying using the PRM ACCESS_REG command.
        * Added support for VAM.  Enabled bad cable EEPROM reporting to the driver.
        * Added support for Platform Level Data Model (PLDM) sideband protocol.
        * Added support for priority based A0-DMFS mode (For further information, please refer to the PRM).
        * Added support for Unicast/Multicast loopback disablement by the driver. (For further information, please refer to the PRM)
        * Removed the source IP from the hash calculation (For further information, please refer to the PRM)
        * Added support for Inline Receive mode up to 2KB.
        * Sideband moved to port 0
        * Added MCTP command support
        * Changed the HP LED scheme for the 779799-B21 adapter.
      
      **Firmware for the following devices are updated to 14.18.2030****:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
        * Added logical link indication in SFP to BaseT modules and disabled logical link when peer port is down.
        * Added support for 10GbE in 25GbE SFP optical modules.
        * Enables mlxlink tool to collect data on the PHY link status and provides link down reasons and additional link related information.
        * Enabled TX configuration response and movement during Link Training in Ethernet.
        * Added support at lane rate of 12.89Gb.
        * Limits the amount of time a packet may head a Traffic Class (TC) transmission queue, without being transmitted. Stale packets are discarded. Active by default for TCs adhering to link level flow control.
        * UAR page size currently is set to 4KB and not according to what the system page size determines.
        * Improved performance of:  
       Doorbell from User Access Region (UAR)  
       Clear interrupt from User Access Region (UAR)
      
        * Added support for additional transport counters.
        * Added ODP support for DC.
        * Enabled scatter-to-CQE for sent packets for DC.
        * Enabled moderation period modification in CQ modify command.
        * Added support for minimum/maximum rate limit per vport in SR-IOV.
        * Enabled network traffic between UEFI-Shell and OS.
        * Enabled the PF to force disable RoCE for its VFs.
        * Added 2 new access registers:  
       Management Capabilities Mask Register  
       Ports CApabilities Mask Register Fields  
      For further information, please refer to the PRM.
      
        * Enabled VNIC the control to enable/disable its local loopback traffic.
        * Added the option to open a receive RDMA Flow Table and to forward RoCE traffic to some destination QP.
        * Added support for Multi-Host LID base routing. This feature requires a new OpenSM (v4.7.1 and above which comes with MLNX_OFED 3.3-2.0.0.0) with the following attributes:  
       qos TRUE  
       lmc 2 (if there is no quad host in the fabric, you can set the lmc to 1)  
       virt_enabled 2 Note: Multi-Host LID base routing can be configured by the
      INI only. The default is 0
      
        * Resilient RoCE is the ability to send RoCE traffic over a lossy network (a network without flow control enabled), without the need to enable flow control on the network. The ability is accomplished by enabling ECN on both the Switch and the Host.
        * Enables load balancing in the Multi PF Switch layer (MPFS) based on the L3/L4 headers
        * Increased the number of VFs from 64 to 95 per Physical Function (PF). Note: When increasing the number of VFs, the following limitations must be taken into consideration: server_total_bar_size >= (num_pfs)*(2log_pf_uar_bar_- size + 2log_vf_uar_bar_size*total_vfs) server_total_msix >= (num_pfs)*(num_pf_msix + num_vfs_msix *total_vfs) Note: For the maximum number of VFs supported by your driver, please refer to your drivers' Release Notes or User Manual.
        * Added support for Port Flap Counter.
        * Limits the buffer size for all entries to improve performance. KSM is used when associating Key Length My Virtual Address (KLMs) with fixed memory size.
        * This entry (null_mkey) is use to indicate non-present KLM/KSM entries. When accessing is, it causes the device to generate page fault event.
        * PLDM firmware burning is based on the DMTF spec DSP0267 (draft 9). The feature enables upgrading firmware and expansion ROM images using the PLDM protocol over MCTP (over PCIe). By doing so, a supporting BMC can query and upgrade the firmware without using OS based tools.
        * Added a new physical layer statistics counters group. The new group includes BER counters, FEC error correction, clear time, and additional physical layer counters. For further information, please refer to the Ethernet Adapters Programming Manual (PRM).
        * Enables the user to set a certain link up state for an unlimited period of time. This mode has 3 states:  
       Aux power (standby)  
       Reboot/boot/driver unloaded - the server is active and no driver is up  
       Driver is up - at least one driver is up (the time between init HCA and
      teardown or FLR)
      
        * Added support for Doorbell from User Access Region (UAR).
        * [Beta] Added support for maximum rate limit per function in SR-IOV.
        * Allows the user to configure the adapter card to stop sending pauses after x when the receive port is unavailable (in a hang state).
        * [Beta] Added support for new performance counters.
        * DCBX is used by DCB devices to exchange configuration information with directly connected peers. DCBX uses Link Layer Discovery Protocol (LLDP) to exchange parameters between two link peers. For further information, please refer to the PRM.
        * Allows network port registers to revert to their default values when the driver is restarted or the host is rebooted.
        * Added additional network link up modes. The new modes decide when to keep the network link up. The new modes are:  
       keep_eth_link_up  
       keep_ib_link_up  
       keep_link_up_on_boot  
       keep_link_up_on_standby
      
        * Added v1, v3, v6 tags to VPD read only tag
        * Enables software to scatter or strip FCS in RQ.
        * Keeps track of the creation of a packet. A time-stamping service supports assertions of proof that a datum existed before a particular time. 
        * Applies pause functionality to specific classes of traffic on the Ethernet link.
        * Custom port counters provide the user a clear indication about RDMA send/receive statistics and errors
        * The Link Layer Discovery Protocol (LLDP) is a vendor-neutral Link Layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on a IEEE 802 LAN. The protocol is formally defined in IEEE 802.1AB.
        * ConnectX-4 adapters now support 1Gb/s and 56GbE Ethernet connectivity in addition to 10GigE, 25GigE, 40GigE, 50GigE, and 100GigE.
        * Provides a clear indication of Flow Steering statistics and errors.
        * The minimal amount of packet headers inlined in the WQE's Eth Segment.
        * A flow table may include a table-miss flow entry, which renders all Match Fields wildcards. If a packet does not match a flow entry in a flow table, this is a table miss. The behavior on a table miss depends on the table configuration. A table-miss flow entry in the flow table may specify how to process unmatched packets.
        * Single Root IO Virtualization (SR-IOV) is a technology that allows a physical PCIe device to present itself multiple times through the PCIe bus.
        * Uses the HCA for offloading erasure coding calculations.
        * Enables the administrator to add a timestamp to the firmware they want to upgrade to avoid situations where one host tries to upgrade the firmware and another tries to downgrade; which may lead to two or more unnecessary server reboots. For further information, please refer to MFT User Manual.
        * The change includes the following:  
      1\. Changed port configuration which required link re-training (such as speed)  
      2\. PAOS down  
      3\. PAOS up  
      This change, will cause the link to toggle and new configurations to take
      effect.
      
        * Flint utility allows performing an MD5 checksum on the non-persistent sections of the firmware image. For further information, please refer to MFT User Manual.
        * Improved TX signal integrity for Electromagnetic Induction (EMI) compliance.
        * Optic modules thermal sensing - Enables the firmware to read and report the temperature of the module.
        * PLDM for module thermal sensing - Supports platform-level data models and platform functions in a platform management subsystem. PLDM is designed to be an effective interface and data model that provides efficient access to low-level platform inventory, monitoring, control, event, and data/parameters transfer functions.
        * Low power boot state - Enables u-boot to put non-boot CPUs into a low power status. To enable low power boot using iLO debugger use the following commands.  
                            * Port shutdown due to optic thermal event - Enables the firmware to close the power cage in case of high temperature in the module.
        * Reduced the port link-up time when negotiating according to Clause 73 (DME)
        * Large Receive Offload (LRO)  Large Send Offload (LSO)
        * Receive Side Scaling (RSS)
        * Global Pause  RoCEv1.0/RoCEv2.0
        * Flow Steering
        * Sniffer Ethernet
        * Rate Limiter (at Beta level)
        * Multi packet WQE
        * Enhanced Transmission Selection standard (ETS)
        * Explicit Congestion Notification (ECN)
        * Priority Flow Control (PFC)
        * CQE time stamping
        * PCIe Function Level Reset (FLR)
        * Power Management L2/L3 flow support
        * Strided SRQ
        * Self Loopback support
        * Transport Domain support
        * CQ2EQ remapping
        * Added support for the following commands:  
       MODIFY/QUERY_ESW_VPORT_CONTEXT  
       QUERY/MODIFY_CONG_STATUS  
       QUERY/MODIFY_CkONG_PARAMS  
       QUERY_CONG_STATISTICS  
       ADD/DELETE_VXLAN_UDP_DPORT


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5-4.1
changelog:
  -     *Fixes in 2.40.7000:**
      
        * Fixed a race between the firmware and the hardware during driver start which blocked outbound completions.
        * Fixed an issue which caused the firmware not to send link_down event to the driver when running the close_port command.
        * Fixed an issue where in rare cases the Auto Sense failed to detect the right protocol.
        * Fixed signal integrity issue when connecting a WCS ConnectX4 mezz card to Pikes peak FPGA..
        * Added the option to transmit corrupted DME pages for a very short period of time at the beginning of the Auto-Negotiation flow.
        * Fixed an incorrect report of the PortRcvDataVLExtended / PortXmitDataVLExtended counters by the firmware.
        * Fixed a rare issue which caused firmware's packet injector to cut off packets when the TX was congested.
        * Fixed an issue that caused the response to TX requests to take up to 10 mili-seconds in IEEE clause 72 Link Training.
        * Fixed a race between 2 iriscs which caused a QP to get stuck in burst control limit state.
        * When a QP was in error state, the firmware generated too many err CQEs at once, thus causing the cmdif responsiveness to be too slow. To prevent the above, the number of err CQEs was limited to 16 at a time.
        * Fixed an issue that caused the MAC address that was set from the OS using ifconfig to be not reflected in the OCBB buffer.
        * Fixed an issue where the ibdump got broken when running with loopback traffic.
        * Fixed an issue where the firmware took QP to firmware ownership and then released it to the hardware ownership without checking if another firmware flow owns the same QP.
        * Fixed an issue which occurred after disconnecting cable which showed the link type as IB even if the link type of the port is ETH.
        * Fixed an issue related to the HCA PoerXmitWait counter on port 2 (connected to port 2 on Switch-IB) where it started counting and reached 0xFF's regardless of connection to switch.
        * Fixed a completion error issue when ECN was enabled. The ECN usage caused ordering errors in completion queues (CQ).
        * Fixed the length calculation of UDP. The incorrect UDP length in the CNP packet caused miss-calculation of the ICRC.
        * Fixed a wrong returned status in cable info MAD when the cable was not connected
        * Fixed failure instances when initiating FLR in the Physical Function.
        * Disabled High Rate Steering mode in the INI to enable its compatibility with NC-SI over VLAN.
        * Fixed a default hardware configuration issue which caused RDP over IPv4 traffic to be dropped.
        * MLNX_OEM command GET_TEMP returned a wrong value in the max_temp field.
        * Fixed an issue which caused TX traffic to stop when the message MTU size was larger than QP.mtu.
        * Fixed an issue which caused NVCONFIG to fail when the number of sector was set to 1 and the sector was zeroed.
        * Fixed a race in handling a duplicated "read request from middle".
        * Fixed an issue which caused lack of IB traffic on SR-IOV VPI.
        * Fixed an issue which caused NVRAM to get stuck when it filled non-valid information in TLV.
        * Fixed an issue which caused an internal firmware error when APM changed the QPs port mapping. 
        * Fixed an issue which caused a firmware internal error when handling QP alternative context. 
        * Fixed an issue which caused packet transmission to get stuck when the software tried to send pause frames with dmac equal to one of the device's MAC addresses.
        * Fixed a wrong reporting of section 5 event 8 - LSO support.
        * Fixed a mistakenly dropped ETH packet with ethertype 0x600 by the NIC.
        * Fixed a case preventing broadcast traffic from arriving to their destination after detaching high priority broadcast rule on a port where NC-SI was enabled.
        * Fixed an issue where the port raised as SDR vs. InfiniScale IV QDR Switch
        * Fixed a rare case of completion Error with Bad Opcode sequence status which occurred when retransmitting read requests
        * Fixed a case where the actual bandwidth did not match the user settings in VM QoS.
        * Fixed a case where on rare cases, communication to BMC was lost during driver initialization.
        * Fixed an issue with cable reading, which caused the link not to raise.
        * Set the maximum EQN number to 1024.
        * Fixed a rare issue with VPD init flow which caused read failures.
        * Fixed an issue with RX size counter not being reported.
        * Fixed promiscuous mode compatibility with A0-DMFS steering.
        * Fixed promiscuous mode compatibility when NC-SI is enabled and configured.
        * Fixed sending/receiving OEM temp commands (set/get) with channel ID 0x1f failure.
        * Fixed an issue which caused packets to drop on a port when changing the interface state of the other port.
        * Fixed long management communication loss and SOL hang during reboot cycles.
        * Fixed wrong processing of inbound traffic towards BMC which caused communication loss.
        * Fixed management link loss upon closing port interface through the driver.
        * Fixed a false indication in firmware of an expander presence causing delay in EEPROM reading.
        * Fixed an issue which caused a link down on a port when the cable was removed from the other port.
        * Fixed a rare case where packet with length zero got stuck in hardware queues.
        * Fixed an issue which caused InfiniBand congestion control packet (CNP) to hang in hardware.
        * Fixed an issue which caused AEN to be sent after channel reset.
        * Fixed an issue which prevented the restoring of QoS setting to its default consequently causing bandwidth degradation.
        * Fixed an occasional long link up time with 10GbE based devices.
        * Fixed an issue preventing cable readings from i2c slave address 0x51
        * Fixed a wrong parity bit calculation when transmitting PCIe TS1 packets.
        * Fixed a possible deadlock in PM turnoff request transmission and ack acceptance flow.
        * Fixed a rare case with alignments state machines which caused occasional width degradation.
        * Fixed an issue where the transmit queues hanged while congestion control was enabled and operational (EQC/QCN)
        * Fixed an unexpected work completion syndrome with vendor syndrome 0x77 received when running RDMA SEN/WRITE traffic with retransmissions.
        * Fixed an issue which caused SetPortInfo to return a good status when receiving invalid LinkSpeedEnabled value.
        * Fixed an issue which caused dual port SFPP module cards to be automatically mapped with expander.
        * Fixed an issue where firmware overrides the steering mode that was chosen by the driver.
        * Fixed invalid return sensing results occurred when the link was up.
        * Fixed an issue causing the sensing result to be delayed when cable was unplugged.
        * Fixed an issue causing the link type to be displayed as ETH when set to AUTO.
        * Fixed an issue causing ARP not to reply when connected to Hyper-V vSwitch.
      
      **Fixes in 14.18.2030****:**
      
        * On rare occasions during UEFI boot cycles system got stuck while WinPE is loaded. (OS WinPE, system DL160).
        * Single FTE that catches both untagged and prio-tagged packets (by giving an FTE with match_value.vlan_tag = 0 and match_value.vid = 0) is currently not supported.
        * Flashing the firmware requires server reboot. Firmware cannot be flashed twice without server reboot after first flashing
        * If the vport state is DOWN and a packet is sent in local loopback, the sx_sniffer tool will not function.
        * Fixed an issue causing bubbles to appear as symbol errors when link raised FDR 1x.
        * When Clause 74 Fire-Code FEC is active, and there are FC corrected errors, both the FC_correctable counter and the FC_uncoreectable counter are increment.
        * Some Port Control Register do not return to the default value after the last port owner host restarts the driver.
        * Fixed an issue which caused RX to hang when the UDP packet had a reserved UDP destination port.
        * Fixed DMAC reporting mapping per host.
        * Fixed an EEH error from PCI which caused firmware to hang.
        * Fixed the default value of the PCIe target_link_speed to Gen3 in link control2.
        * Fixed an issue which prevented LEDs from blinking when the traffic was less than 0.1% of the link speed.
        * Fixed an issue which caused the mlxconfig configuration of VF_LOG_BAR_SIZE to be ignored and to be set to 5 (32MB).
        * A server getting into a Standby mode while Packet-Pacing is enabled might cause firmware to hang and driver call-trace.
        * Fixed an issue which caused unexpected QoS functionality in case of multiple sources to single destination traffic transmission.
        * Fixed an issue which occasionally caused the RX traffic to hang in DC when received a PCI error on WQE fetch.
        * Fixed OOB connection issue during Intel's ITP inject errors test.
        * Fixed an issue which prevented MAC address changes by to driver to be reflected in the OBCC and NC-SI interfaces.
        * Added protection from IOPX thermal diode destabilization to prevent UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GE cards.
        * Fixed an issue which caused a link down in Port 2 when unplugging the cable from Port 1.
        * In some cases, a Bit Error Rate is not optimal on 10G/40G links.
        * Instability of Link Training Flow occurs during 100G Auto-Negotiation.
        * Fixed a rare issue which caused the command to hang when moved the QP to RESET and back to RTS.
        * Improved RDMA READ bandwidth under packet lost scenario.
        * Added support for pnat = 1 in HCA access_reg command as required by the ibdiagnet tool.
        * Fixed the LLDP OCBB response: return value is now ascii.
        * Fixed a very rare NMI issue during PXE cycles.
        * Increased the steering hash tables static size from 128 to a maximum of 32K entries.
        * Prevented miscalculation of module temperature when using 100Gb/s cables (OPN: MFA1A00-Cxxx for 100GbE).
        * Reduced one hop for Unicast RX steering, steering pipes balancing.
        * Non-volatile configuration of Port Type TLV more than 50 times might cause system hang.
        * Enabled RoCE IPv4 Multicast. This prevents MCG command from failing when an IPv4 is mapped to an IPv6 address.
        * If the PF driver or the tool (e.g. ethtool) use PAOS DOWN command (e.g. by ifconfig down or ip link set down), loopback traffic is blocked for all functions on this port (PF<->VFs / VF<->VF) In Multihost loopback, the traffic will be blocked once the firmware receives the PAOS down command from all PFs. However, the loopback traffic will not be blocked when the port is down  due to the physical link (for example: cable plugged out, switch port down).
        * Fixed a 25G and 50G link issue when Clause 91 RS FEC was active.
        * Added a missing invalidation of eSwitch cache upon FLR which caused the upcoming driver load to either fail or not to be able to transmit.
        * Fixed a UEFI IPv6 PXE boot failure on ConnectX-4 Lx 25GbE OCP card.
        * Fixed an issue which prevented Vport counters from counting local loopback packets. Packets now are filter by the self-loopback prevention.
        * Reported INTx as unsupported to allow PFs Passthrough on PowerKVM.
        * SR-IOV Ethernet supports up to 18 VFs per port only.
        * Fixed and incident what allowed local (internal) loopbacked packets to be counted by the Vport counters, although Vport counters should count only traffic that crosses the Vport.
        * Fixed an issue preventing driver loading or TX traffic sending upon reboot, after ungraceful driver unload.
        * Fixed casting of BMC MAC before steering API.
        * Fixed the PCI write flow to take into consideration the PCI MTU. This fix eliminates the need for NOPs in the flow, which resulted from PPC larger PCI MTU.  
      The single queue limitation for READ is due to a hardware limitation of the
      number of READ request in a given time.
      
        * Fixed a case that caused FlexBoot to not work as expected with systems that run with "large bar" enabled (Above 4G Decoding) over Connect-IB or ConnectX-4 HCAs.
        * Fixed an issue which prevented link creation when connected to IXIA 25G.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.42.5000:**
      
        * Added support for the following features: 
          * TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
        * Enhanced the debug ability for command timeout cases.
        * Added a new field to "set port" command which notifies the firmware what is the user_mtu size.
      
      **Firmware for the following devices are updated to 14.21.2800****:**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **New features and changes in version 14.21.2800:**
      
        * Query vPort Environments (Debug Counters) - Debug counters are a group of counters that handle traffic performance issue related to firmware overhead in transport flow. The following are the additional counters added to this firmware version: 
          * current_q_under_processor_handle
          * total_q_under_processor_handle
          * qp_priority_update_flow


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Fixes submitted in version 2.42.5000:**
      
        * The PortRcvPkts counter was prevented from being cleared after resetting it.
        * Fixed an issue which caused a system Time Out on the configuration cycle of the VFs when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than  
      16 msec.
      
        * Fixed an issue that caused the server to hang and result in NMI when running "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a different thread). In this case, the downstream bridge over the device reported completion timeout error.
        * Fixed an issue in flow_steering where BMC could not receive a ping over IPV6 after running bmc_reboot.
        * Fixed an issue while closing the HCA, where RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * Fixed an issue where the masterSM LID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * Fixed an issue that prevented ibdump from capturing all MADs packets.
        * Fixed an issue that prevented the link to go up after reboot.
        * Fixed a rare issue that cause the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions.
        * Fixed an issue that caused NC-SI not to work when adding the disable_static_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes submitted in version 14.21.2800:**
      
        * Fixed an issue that caused QP connection timeout due to firmware not being able to handle duplicate packets with AckReq bit set. The fix stopped ignoring duplicate AckReq packets to avoid timeout on the sender side.
        * MPFS load balance (DUP_MAC_ACTION==LOAD_BALANCE(1)) is not working as long as IB_ROUTING_MODE/SRIOV_IB_ROUTING_MODE is configured to LID.
        * Fixed an issue that caused a SX engine deadlock (the SX engine handles software port/priority changes for a specific Send Queue) when more than a single SX engine handled the "prio diff" flow simultaneously, thus caused the hardware to get stuck.  
      The issue happened as the firmware releases the SX engine and waits for
      various operation to complete. However, due to a race that allows a different
      transaction to get into the SX engine and cause the lock to be taken by it,
      the SX engine release is prevented.
      
        * Fixed an issue that caused the system to hang while changing QPTS/QPDPM/QPDP parameters during traffic.
        * Fixed unfairness between senders in RoCE LAG while ECN is configured.
        * Fixed an issue which displayed diagnostic counters only on the adapter that was initialized first, which is the counters' owner. The owner received correct values, while the other adapter only received zeros.
        * Fixed an issue that caused the rdma_cm traffic to fail on the 2nd port when more than 32 VFs were configured, when the RoCE Dual Port vHCA (a.k.a Multi-Port vHCA: MPV) feature was enabled.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5000:**  
        
      779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
      779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **New features and changes in version 2.42.5000:**
      
        * Added support for the following features: 
          * TLV: CX3_GLOBAL_CONF to enable/disable timestamp on incoming packets through mlxconfig configuration.
          * User MAC configuration.
          * Automatically collecting mstdump before driver reset.
          * to detect DEAD_IRISC (plastic) from TPT (iron) and raise an assert.
        * Enhanced the debug ability for command timeout cases.
        * Added a new field to "set port" command which notifies the firmware what is the user_mtu size.
      
      **Firmware for the following devices are updated to 14.22.1414 :**
      
      817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
      817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **New features and changes in version 14.22.1414:**
      
        * Transition from 4MB to 7M Firmware Image Banks.
        * **Software Reset Flow:** Software detection of a fatal error, automatic creations of an mstdump file for future debug by the software, and resetting of the device.
        * **Steering Discard Packet Counters:** The following counters were added to count the discard packets (per vport) 
          * nic_receive_steering_discard
          * receive_discard_vport_down
          * transmit_discard_vport_down
        * **Virtual Functions (VF): **Increased the number of VFs that can work with full VMQoS (8 TC) per PFs as follow 
          * in dual port devices to 20 VFs
          * in single port devices to 58 VFs
        * Increased the Pause Frame Duration and the XOFF Resend Time to the maximum value defined by the specification.
        * **PCI Relax Ordering:** mlxconfig configuration can now enable or disable forced PCI relaxed ordering in mkey_context.
        * **vport Mirroring:** Packets are mirrored based on certain mirroring policy. The policy is set using the "set FTE command" that supports forward action in the ACL tables (ingress/egress).
        * **Resiliency: Special Error Event: **Added support for 10GBaseT modules connected to a QSFP cage.
        * Accelerated QP's creation time.
        * SR-IOV default routing mode is now LID based. The configuration change is available via mlxconfig tool.
        * Added PXE and UEFI to additional ConnectX-4 Lx adapter cards. ConnectX-4 Lx now holds PXE, x86-UEFI and Arm-UEFI.
      
      **Firmware for the following device is updated to 12.22.1414 :**
      
      868779-B21 (HPE Synergy 6410C 25/50Gb Ethernet Adapter)
      
      **New features and changes in version 12.22.1414:**
      
        * Transition from 4MB to 7M Firmware Image Banks.
        * **Software Reset Flow:** Software detection of a fatal error, automatic creations of an mstdump file for future debug by the software, and resetting of the device.
        * **Steering Discard Packet Counters:** The following counters were added to count the discard packets (per vport) 
          * nic_receive_steering_discard
          * receive_discard_vport_down
          * transmit_discard_vport_down
        * **Virtual Functions (VF): **Increased the number of VFs that can work with full VMQoS (8 TC) per PFs as follow 
          * in dual port devices to 20 VFs
          * in single port devices to 58 VFs
        * Increased the Pause Frame Duration and the XOFF Resend Time to the maximum value defined by the specification.
        * **PCI Relax Ordering:** mlxconfig configuration can now enable or disable forced PCI relaxed ordering in mkey_context.
        * **vport Mirroring:** Packets are mirrored based on certain mirroring policy. The policy is set using the "set FTE command" that supports forward action in the ACL tables (ingress/egress).
        * **Resiliency: Special Error Event: **Added support for 10GBaseT modules connected to a QSFP cage.
        * Accelerated QP's creation time.
        * SR-IOV default routing mode is now LID based. The configuration change is available via mlxconfig tool.
        * Added PXE and UEFI to additional ConnectX-4 Lx adapter cards. ConnectX-4 Lx now holds PXE, x86-UEFI and Arm-UEFI.
      
      
      
      **Firmware for the following device is updated to 16.22.1414 :**
      
      874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 16.22.1414:**
      
        * Transition from 4MB to 7M Firmware Image Banks.
        * **Software Reset Flow:** Software detection of a fatal error, automatic creations of an mstdump file for future debug by the software, and resetting of the device.
        * **Steering Discard Packet Counters:** The following counters were added to count the discard packets (per vport) 
          * nic_receive_steering_discard
          * receive_discard_vport_down
          * transmit_discard_vport_down
        * Increased the Pause Frame Duration and the XOFF Resend Time to the maximum value defined by the specification.
        * **PCI Relax Ordering:** mlxconfig configuration can now enable or disable forced PCI relaxed ordering in mkey_context.
        * Added support for Push/Pop VLAN, new FLOW TABLE ENTRY actions. These new actions are used by the driver to implement Q-in-Q functionality.
        *  Packet Pacing in ConnectX-5 adapter cards.
        * **vport Mirroring:** Packets are mirrored based on certain mirroring policy. The policy is set using the "set FTE command" that supports forward action in the ACL tables (ingress/egress).
        * **Resiliency: Special Error Event: **Added support for 10GBaseT modules connected to a QSFP cage.
        * Accelerated QP's creation time.
        * SR-IOV default routing mode is now LID based. The configuration change is available via mlxconfig tool.
        * Added PXE and UEFI to additional ConnectX-4 Lx adapter cards. ConnectX-4 Lx now holds PXE, x86-UEFI and Arm-UEFI.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8-2.1
changelog:
  -     *Fixes submitted in version 2.42.5000 :**
      
        * The PortRcvPkts counter was prevented from being cleared after resetting it..
        * System Time Out on the configuration cycle of the VFs when more than 10 Virtual Functions performed FLR and the completion Time Out value was configured to a range of less than 16 msec.
        * The server hung and resulted in NMI (Non-maskable interrupt) when run-ning "mlxfwtop -d mt4103_pci_cr0" while restarting the driver in parallel (from a differ-ent thread). In this case, the downstream bridge over the device reported completion timeout error. 
        * In flow_steering, BMC could not receive a ping over IPV6 after running bmc_reboot.
        * While closing the HCA (Host Channel Adapters), RX packet caused bad access to resources that did not exist, and consequently caused the QPCGW or the irisc to get stuck.
        * The master SMLID and the LID was either 0 or 0xFFFF when the port was neither active nor armed.
        * ibdump could not capture all MADs packets.
        * Link could not go up after reboot.
        * A rare issue caused the PCIe configuration cycle that arrived during the time of sw_reset to generate 2 completions. 
        * NC-SI (Network Controller Sideband Interface) did not work when adding the disable_stat-ic_steering_ini field in the ini file, due to memory allocation issue for this field in the scratchpad.
      
      **Fixes submitted in version 14.22.1414 :**
      
        * A temperature normalization function calculation issue. Now the cable gain that is not pure integer is taken into account was fixed.
        * An issue related to the parser of object 0x8 in ASN that caused different structure in response was fixed.
        * Added the option to avoid unintentionally powering off the backplane port cage upon reboot when in standby mode.
        * An issue that caused the driver to return a wrong logical OR of the 2 physical ports, when querying the vport state when the LAG was enabled wre fixed.
        * Increased the Full Wire Speed (FWS) threshold value to improve EDR link results.
        * An issue that resulted in "Destroy LAG" command failure if a VFs received an FLR while its affinity QPs were open.
        * When RoCE Dual Port mode is enabled, tcpdump is not functional on the 2nd port.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following device is updated to 12.23.8036 :**
      
         868779-B21 (HPE Synergy 6410C 25/50Gb Ethernet Adapter)
      
      **Firmware for the following devices are updated to 14.23.8052 :**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.23.8036 :**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.23.8036 :**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 12.23.8036 , 14.23.8036 and 16.23.8036 :**
      
        * Implemented DCi specification v.0.80. The specification defines the NIC behavior in case of restore factory default while the NIC does not support AUX power.
        * Added support for Abstract Syntax Notation One(ASN1) defaults v3.0 and NIC Discovery Configuration v.0.81
        * Added support for Management Component Transport Protocol (MCTP) over PCI.
        * Added support for Event Description Addendum 2.6.4.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9-2.1
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * Fixed an issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode
      
      **Fixes submitted in version 12.23.8036 :**
      
        * Fixed a Phase-Locked Loop(PLL) tuning issue by improving the tx_clk_phase lock mechanism.
        * The Link Layer Discovery Protocol(LLDP): Removed management MAC 0 address once a new address is received
        * Set the Port ID to be the MAC of the port
      
      **Fixes submitted in version 14.23.8052:**
      
        * The HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter was not linking in AUX power mode.
      
      **Fixes submitted in version 16.23.8036 :**
      
        * Fixed an Active Health System(AHS) packet over PCIe interface issue


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following device is updated to 12.24.9000 :**
      
         868779-B21 (HPE Synergy 6410C 25/50Gb Ethernet Adapter)
      
      **Firmware for the following devices are updated to 14.24.9006 :**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.24.9000 :**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.24.9000 :**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 14.24.9000  :**
      
        * Implemented DCi specification v.0.80. The specification defines the NIC behavior in case of restore factory default while the NIC does not support AUX power.
        * Added support for Abstract Syntax Notation One(ASN1) defaults v3.0 and NIC Discovery Configuration v.0.81
        * Added support for Management Component Transport Protocol (MCTP) over PCI.
        * Added support for Event Description Addendum 2.6.4.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * Fixed an issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode
      
      **Fixes submitted in version 14.24.9006:**
      
        * The HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter was not linking in AUX power mode.
      
      **Fixes submitted in version 16.24.9000 :**
      
        * Fixed an Active Health System(AHS) packet over PCIe interface issue


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.26.1040:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.26.1040 :**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 14.26.1040 and 16.26.1040 :**
      
        * Enabled the firmware by using the ICMD commands to deal with diagnostic counters similar to cmdif.
        * The ICMD Query Caps indicate support and expose the list of the supported counters.
        * Enabled a new feature User Context Object (DEVX) which is a containerized sandbox per user, to access PRM command securely by using General Object commands, UMEM and UCTX contexts. The allowed functionalities of this capability depend on the user permissions.
        * Support for reporting the supported affiliated and unaffiliated asynchronous events to DEVX users through the command interface.
        * Zero-Touch-RoCE counters are now available to the user for debuggability purposes when using the Zero-Touch-RoCE feature.
        * Reliability improvements and security hardening enhancements were done.
      
      **New features and changes in version 16.26.1040  :**
      
        * Added support for the following features: 
          * Address Translation Service (ATS) support for MKEY and UMEM.
          * Exposing the VPD on the VF.
          * Hairpin Drop Counter.
          * Hairpin and TM RNDV QPs to work with DevX.
          * Creating software managed steering tables in eSwitch/FDB.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10-2.1
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **Fixes submitted in version 14.26.1040:**
      
        * A function was misbehaving when a PCIe TLP was set with a poisoned indication.
        * The "destroy mkey " command was getting stuck when rebooting the hypervisor.
        * The total firmware reset time is increased by 1 second.
      
      **Fixes submitted in version 16.26.1040:**
      
        * On rare occasions, when firmware coalesce Host stuck events occur, a async event might be delayed to be reported, and not be triggered until the next time the PCIe hangs on one of the hosts.
        * Unexpected queue pairs transitioned to error in lossy tests.
        * Limited the maximum amount of dumps created on a PF.
        * Renamed the GMP Mellanox Vendor Specific External Capability mask enum from IsDiagnosticCountersSupported to IsDiagnosticDataSupported.
        * Stability issues with RDMA over Converged Ethernet (RoCE) retransmissions under stress were affecting Zero-Touch-RoCE.
        * Fixed an issue that caused a function to misbehave when a PCIe Transaction Layer Packet (TLP) was set with a poisoned indication.
        * Large number of packets dropped when running Jumbo frames with TTL rewrite.
        * Limited the number of the elements in the Quality of Service (QoS) tree 2K.  
      Note: Creating more than 250 Vport_tc for every TC is not allowed.
      
        * Queue Pair (QP) flow query was always taking port 1, Firmware will now reply the proper port, 1 or 2, for the dual port RoCE net device.
        * The nack counters constantly reported as "0".
        * In a rare scenario when the driver is executing the "2err" command and the QP is in Send Queue (SQ) drain state, the firmware might post event of broken Work Queue (WQ) instead of sending error Completion Queue Element (CQEs) on all the Work Queue Entry (WQEs).


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.11
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.26.1040:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.26.1040 :**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.26.1040 :**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 14.26.1040 and 16.26.1040 :**
      
        * Enabled the firmware by using the ICMD commands to deal with diagnostic counters similar to cmdif.
        * The ICMD Query Caps indicate support and expose the list of the supported counters.
        * Enabled a new feature User Context Object (DEVX) which is a containerized sandbox per user, to access PRM command securely by using General Object commands, UMEM and UCTX contexts. The allowed functionalities of this capability depend on the user permissions.
        * Support for reporting the supported affiliated and unaffiliated asynchronous events to DEVX users through the command interface.
        * Zero-Touch-RoCE counters are now available to the user for debuggability purposes when using the Zero-Touch-RoCE feature.
        * Reliability improvements and security hardening enhancements were done.
      
      **New features and changes in version 16.26.1040  :**
      
        * Added support for the following features: 
          * Address Translation Service (ATS) support for MKEY and UMEM.
          * Exposing the VPD on the VF.
          * Hairpin Drop Counter.
          * Hairpin and TM RNDV QPs to work with DevX.
          * Creating software managed steering tables in eSwitch/FDB.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.11-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.26.4012:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.26.4012:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 14.26.4012 and 16.26.4012:**
      
        * Enables the user to globally disable RoCE on init by writing to the access register NCFG_REG.
        * Enabled Zero-Touch RoCE (ZTR) slow start capability for responder flows.
        * Extracts and prints data segments generated by the firmware.
        * Hairpin QP buffer is now available in Flow Control. Host Chaining now supports full fairness between several devices.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.11-2.1
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **Fixes submitted in version 14.26.4012:**
      
        * Fixed an issue that resulted in dump file being corrupted when using resource dump to dump a WQ buffer with a size more than 2^16 bytes.
        * Enabled the option to prevent clock and capture complex programmable logic device (CPLD general-purpose input/output (GPIO)s glitch upon firmware reset.
      
      **Fixes submitted in version 16.26.4012:**
      
        * Fixed a rare issue that caused the device to hang when encountering Remote Direct Memory Access (_RDMA_) read operations with very short retry time. In this case, the driver failed to load due to wait_fw_init (mlx5_load_one failed with error code -16).
        * Increased the bandwidth for RoCE scenarios using a specific Quantum Private Network (QPN).
        * Enabled lower granularity of rate for Congestion Control.
        * Set the min_time_between_cnps default value as 2.
        * Fixed an issue that prevented the meter counter from being cleared after the flow meter being updated. In this case, the Information rate took up to 10 minutes to take effect.
        * Fixed an issue that caused a unequal cost multipath when device set the lag_tx_port_affinity of the Queue Pair(QP).
        * Fixed a performance degradation issue that occurred when the flow group match criteria includes both IPV6 and IP_ECN.
        * Fixed a low performance issue that occurred occasionally when ran firmware steering with high insertion rate during "adding and removing" low table entries.
        * When working with Multi-GVMI and SR-IOV, and with a high number of Virtual Functions and sub-functions, the driver start may fail for the VFs/sub-functions.
        * Fixed a performance issue that occurred when ran numerous VMs with NIC Steering rules.
        * sw_reset action fails in case it was initiated during live-patch flow.
        * SX_RDMA was not supported when Dual Port RoCE feature is enabled. Due to this behavior, packets sent on other port are be processed by the SX_RDMA table.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.12
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.27.1016:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.27.1016:**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.27.1016:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 14.27.1016 and 16.27.1016:**
      
        * RoCE Selective Repeat : This feature introduces a new QP (Queue Pair) retransmission mode in RoCE: recovery from packet drop by resending the dropped packet and not only all the PSN window (Go-Back-N protocol),  
      This new capability comes with the following limitations:
      
          * Selective repeat cannot be used with AR.
          * Does not work with signature (T10-DIF).
          * Does not work with Tag Matching enabled.
        * Allows BMC (Board Management Control) to query and control NIC over RedFish API. Currently, the NIC supports reading data and setting basic Ethernet and InfiniBand parameters.
        * Enables matching of source_vhca_port in the FDB also known as FIB ( Forwarding Information Base) flow for ECMP (Equal Cost Multi Pathing) hardware offload on a single FDB.
        * Firmware can be now updated as well as DB strings while performing Live Firmware Patch.
        * Added support for dumping hardware steering entries (raw data) using the resource dump API.
        * The eth_link_down_counter now counts logical link downs as well.
      
      **New features and changes in version 16.27.1016:**
      
        * Removed power consumption limitation.This new capability removes the necessity to disable the port due to insufficient power. When this feature is enabled, an event will be sent on every transition between the following power states: 
          * Power limit is not advertised.
          * Sufficient power detected.
          * Insufficient power detected.
        * Enables the device to generate events that will notify the user about any resource dumps updates. The resource dump owner (PF/ECPF) will be notified on the VF command failures by events that will contain the needed information to call the resource_dump command. The device will dump the resource in the standard resource dump sequence.
        * Added support for RSS (Really Simple Syndication) based on inner headers of GTP-U tunneled packets and for relaxed ordering read when using the create_mkey flag.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.12
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **Fixes submitted in version 14.27.1016:**
      
        * An issue that caused the device to perform DMA (Direct Memory Access) into memory already returned to the OS during the transition between the pre-boot driver to the OS driver.
        * An issue that caused the ZTR (Zero Touch RoCE) counters query to always return 0.
        * NC-SI bandwidth was dropping to 20-40kBps with a high amount of package drops, in a network environment with high latency (over 110ms).
      
      **Fixes submitted in version 16.27.1016:**
      
        * An issue that caused the device to perform DMA (Direct Memory Access) into memory already returned to the OS during the transition between the pre-boot driver to the OS driver.
        * An out-of-range issue when reading or writing the q_counters was fixed.
        * Multi-Host adapter cards that resulted in wrong handling of PERST on auxiliary links.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.13
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HP Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HP Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.27.4000:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.27.4000:**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.27.2008:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 16.27.2008:**
      
        * Added the following segments, as appeared in the PRM, to the Resource Dump: 
          * PRM_QUERY_QP
          * PRM_QUERY_CQ
          * PRM_QUERY_MKEY
          * QUERY_VNIC_ENV
      
      **New features and changes in version 14.27.4000:**
      
        * Added mlxconfig support for power reduction: 
          * PCI CAP
          * AUTO_POWER_SAVE_LINK_DOWN


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.13
changelog:
  -     *Fixes submitted in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **Following issues have been fixed in firmware version 14.27.4000:**
      
        * The sent packet hung while the device entered FLR mode.
        * Enabled Bar configuration bytewise by applying the write_en bitmask.
        * The device hung while running the sw reset flow under heavy stress and with many open resources.
        * The completions (CQ)completed due to a race condition in the firmware transport error handlers, and the error stressors, where the error stressors would hang the firmware transport error handler flow. 
        * The fragmented IP packets were dropped.
      
      **Following issues have been fixed in firmware version 16.27.2008:**
      
        * Although the effective BER (after FEC) was expected to meet the design targets (e.g. 10e-14 or lower), occasionally it was higher.
        * High BER occured when connecting cables of type 0.5/1m DAC to an HDR speed.
        * The PCIe Tx parameters did not load correctly when the speed was changed after the PCIe link was disabled.
        * The desched_threshold field did not work properly.
        * The "roce_adp_retrans" counter was presenting the values of the "local_ack_timeout_err" counter.
        * If Relaxed Ordering was disabled by running the "setpci" command, it would not be functional even after re-enabling it by running the "setpci" command again.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.29.1016:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.29.1016:**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.29.1016:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New features and changes in version 14.29.1016:**
      
      Added support for the following features:
      
        * A new counter per vPort that counts the number of packets that reached the Ethernet RQ but cannot fit into the WQE due to their large size. Additionally, we added the option to control if such packet will cause "CQE with Error" or "CQE_MOCK".
        * cq_overrun counter: This counter represents the number of times CQs enter an error state due to overflow that occur when the device tries to post a CQE into a full CQ buffer.
        * Enabled the capability to allow Virtual Functions to send Pause Frames packets.
        * Enabled 10/25GbE auto-sensing with 3rd party when using 10/25GbE optical cables.
        * Hardware steering dump output used for debugging and troubleshooting.
      
      **New features and changes in version 16.29.1016:**
      
      Added support for following features:
      
        * An option to allow applications to build their own QoS tree over the NIC hierarchy by connecting QPs to responder/requestor Queue Groups.
        * "InfiniBand" properties set to the Network Device Function Redfish object.
        * HW support for Flow Metering to utilize Advanced Steering Operation (ASO). HW Flow Meter allows higher scale, more accuracy, and better performance compare to the FW Flow Metering.
        * Trust level for VFs. Once the VF is trusted, it will get a set of trusted capabilities.
        * 2 new Mini CQE formats: Responder Mini CQE With Flow Tag Layout Responder Mini CQE With l3_l4_info Layout
        * UCX can now enable AR by exposing Out-Of-Ordering bitmask per SL with "ooo_per_sl" field in the HCA_VPORT context. It can be also queried by running the QUERY_HCA_VPORT_CONTEXT command.
        * Steering DP hash flow groups.
        * A new counter per vPort that counts the number of packets that reached the Ethernet RQ but cannot fit into the WQE due to their large size. Additionally, we added the option to control if such packet will cause "CQE with Error" or "CQE_MOCK".
        * PCIe Rx modifications to prevent the adapter cards from disappearing from the system.
        * ignore_flow_level is now enabled by the TRUST LEVEL access registry. 
        * cq_overrun counter. The counter represents the number of times CQs enter an error state due to overflow that occur when the device tries to post a CQE into a full CQ buffer.
        * [Beta] Enabled the capability to allow Virtual Functions to send Pause Frames packets.
        * Enabled 10/25GbE auto-sensing with 3rd party when using 10/25GbE optical cables.
        * Hardware steering dump output used for debugging and troubleshooting.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14
changelog:
  -     *ixes submitted in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **Following issues have been fixed in firmware version 14.29.1016:**
      
        * Changed the default value of DCQCN's (Data center- Quantized Congestion Notification)  NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        * An issue that caused packets to drop due to header size issues and/or failing checks. The issue was caused due to a Linux issue that caused VFs to set the wrong header size value in wqe_inline_header_mode input.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs were configured, VM restart (VF/PF FLR) will take longer than when MKEY_BY_NAME is disabled.
        * On rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.
        *  An issue that caused the device to go to dead IRISC as one of the firmware semaphores could not be released when a speed change or port state change was triggered. 
      
      **Following issues have been fixed in firmware version 16.29.1016:**
      
        * Changed the default value of DCQCN's (Data center- Quantized Congestion Notification) NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        *  An issue that prevented VXLAN packets with svlan/ cvlan tag from being matched.
        * The eth_wqe_too_small counter to count ODP page used to fail.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs are configured, VM restart (VF/PF FLR) will take longer than when MKEY_BY_NAME is disabled.
        * An issue that resulted in low performance after enabling the RoCE Accelerator capability.
        * On rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.
        * The chassis manager calculation for Multi-Host and Socket-Direct adapter cards to allow running NC-SI commands by the chassis manager BMC. Now the chassis manager is count as BMC with index 0, regardless of how many BMC there are.
        * An issue that caused the device to go to dead IRISC as one of the firmware semaphores could not be released when a speed change or port state change was triggered.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.31.1200:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.29.1016:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      **New Features and Changes included in version 16.31.1200:**
      
        * Added a new NVconfig per Port for a specific Finisar module. This new NVconfig sets the port to work in AN mode and sets the module to No Data Management Engine (DME). This change does not affect the speed logic, only the forward error correction (FEC) logic (FEC override). **Note:** If the port does not come up, switch to Force mode. 
      
      **New features and changes included  in version 16.29.1016:**
      
        * An option to allow applications to build their own QoS tree over the NIC hierarchy by connecting QPs to responder/requestor Queue Groups.
        * "InfiniBand" properties set to the Network Device Function Redfish object.
        * HW support for Flow Metering to utilize Advanced Steering Operation (ASO). HW Flow Meter allows higher scale, more accuracy, and better performance compare to the FW Flow Metering.
        * Trust level for VFs. Once the VF is trusted, it will get a set of trusted capabilities.
        * 2 new Mini CQE formats: Responder Mini CQE With Flow Tag Layout Responder Mini CQE With l3_l4_info Layout
        * UCX can now enable AR by exposing Out-Of-Ordering bitmask per SL with "ooo_per_sl" field in the HCA_VPORT context. It can be also queried by running the QUERY_HCA_VPORT_CONTEXT command.
        * Steering DP hash flow groups.
        * A new counter per vPort that counts the number of packets that reached the Ethernet RQ but cannot fit into the WQE due to their large size. Additionally, we added the option to control if such packet will cause "CQE with Error" or "CQE_MOCK".
        * PCIe Rx modifications to prevent the adapter cards from disappearing from the system.
        * ignore_flow_level is now enabled by the TRUST LEVEL access registry. 
        * cq_overrun counter. The counter represents the number of times CQs enter an error state due to overflow that occur when the device tries to post a CQE into a full CQ buffer.
        * [Beta] Enabled the capability to allow Virtual Functions to send Pause Frames packets.
        * Enabled 10/25GbE auto-sensing with 3rd party when using 10/25GbE optical cables.
        * Hardware steering dump output used for debugging and troubleshooting.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.14-2.1
changelog:
  -     *Fixes included in  firmware version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **Fixes included in firmware version 14.29.1016:**
      
        * Changed the default value of DCQCN's (Data center- Quantized Congestion Notification)  NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        * An issue that caused packets to drop due to header size issues and/or failing checks. The issue was caused due to a Linux issue that caused VFs to set the wrong header size value in wqe_inline_header_mode input.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs were configured, VM restart (VF/PF FLR) will take longer than when MKEY_BY_NAME is disabled.
        * On rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.
        *  An issue that caused the device to go to dead IRISC as one of the firmware semaphores could not be released when a speed change or port state change was triggered. 
      
      **No fixes are included in firmware version 14.31.1200.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.15
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.31.1200:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.31.1200:**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.31.1014:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
        
      **New features and changes in version 14.31.1200:**
      
        * NVconfig per Port for a Specific Finisar Module: Added a new NVconfig per Port for a specific Finisar module. This new NVconfig sets the port to work in AN mode and sets the module to No DME. This change does not affect the speed logic, only the FEC logic (FEC override).  
      **Note:** If the port does not go up, switch to Force mode. 
      
      **New features and changes in version 16.31.1014:**
      
        * NIC scheduling feature support has been disabled for non-privileged functions.
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * Added support for Enabling/Disabling NIC and RDMA (port/partition) via the UEFI HII system settings.  
      **Note:** Values set in this option only take effect when is Ethernet mode.
        * Increased the maximum number of MSIX per VF to 127.
        * Asymmetrical MSIX Configuration: This feature allows the device to be configured with a different number of MSIX  
      vectors per physical PCI functions.  
      To use this feature, please follow these steps:
      
          * Clear NUM_PF_MSIX_VALID to disable global symmetrical MSIX configuration.
          * Set PF_NUM_PF_MSIX_VALID to enable asymmetrical per Physical Function MSIX configuration.
          * Configure PF_NUM_PF_MSIX per physical PCI function.
        * Support for RDMA partitioning and RDMA counters in IB mode.
        * A new bit ("data_in_order") was added to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.  
      Pages are returned by the driver to the kernel without issuing the
      MANAGE_PAGES commands to the firmare.
      
        * Enabled UID 0 to create resources with UMEM (User Memory).
        * Receiving and sending native IB packets from/to the software (including all headers) via raw IBL2 QPs.
        * RX RDMA NIC flow table on an IB port. Now the software can steer native IB packets to raw IB receive queues according to the DLID and  
      the DQPN.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.15
changelog:
  -     *Fixes included in  firmware version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.31.1200:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1200:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.
      
      **The following issues have been fixed in version 16.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * An assert that was caused when trying to open 1024 functions on the device and the maximum number of functions was 1023.
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to hang.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
      
      **Additional Fixes included in version 16.31.1014:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.15-2.1
changelog:
  -     *Firmware for the following devices are updated to 2.42.5044 :**
      
         779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)  
         779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices are updated to 14.31.1200:**
      
         817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
      
      **Firmware for the following devices are updated to 14.31.1200:**  
         817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device is updated to 16.31.1014:**
      
         874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **Updated mstflint from version 4.13 to 4.16**
      
        
      **New features and changes in version 14.31.1200:**
      
        * NVconfig per Port for a Specific Finisar Module: Added a new NVconfig per Port for a specific Finisar module. This new NVconfig sets the port to work in AN mode and sets the module to No DME. This change does not affect the speed logic, only the FEC logic (FEC override).  
      **Note:** If the port does not go up, switch to Force mode. 
      
      **New features and changes in version 16.31.1014:**
      
        * NIC scheduling feature support has been disabled for non-privileged functions.
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * Added support for Enabling/Disabling NIC and RDMA (port/partition) via the UEFI HII system settings.  
      **Note:** Values set in this option only take effect when is Ethernet mode.
        * Increased the maximum number of MSIX per VF to 127.
        * Asymmetrical MSIX Configuration: This feature allows the device to be configured with a different number of MSIX  
      vectors per physical PCI functions.  
      To use this feature, please follow these steps:
      
          * Clear NUM_PF_MSIX_VALID to disable global symmetrical MSIX configuration.
          * Set PF_NUM_PF_MSIX_VALID to enable asymmetrical per Physical Function MSIX configuration.
          * Configure PF_NUM_PF_MSIX per physical PCI function.
        * Support for RDMA partitioning and RDMA counters in IB mode.
        * A new bit ("data_in_order") was added to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.  
      Pages are returned by the driver to the kernel without issuing the
      MANAGE_PAGES commands to the firmare.
      
        * Enabled UID 0 to create resources with UMEM (User Memory).
        * Receiving and sending native IB packets from/to the software (including all headers) via raw IBL2 QPs.
        * RX RDMA NIC flow table on an IB port. Now the software can steer native IB packets to raw IB receive queues according to the DLID and  
      the DQPN.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.16
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.32.1010:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.32.1010:**
      
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for QSHR access register to enable Set and Query rate limit perhost per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.16
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * The system could not create more than 128K QPs.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
        * PCIe lane margining capability issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.17
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.33.1048:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter.
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.17
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.33.1048:**
      
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * The card occasionally masked some PCIe AER reporting.
        * Incorrect flow of credits blockage that prevented booting during DC cycle test.
        * An issue with BMC medium migration from SMBUS to PCIe, and increased FIFOs to pass large packets in case of the migration.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.18
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.34.1002:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.34.1002:**
      
        * Added LLDPEnable, LLDPTransmit and LLDPReceive properties to the RDE Port schema implementation.
        * Added "Command Unsupported" response code in cases when running the MCTP control command "Get Vendor Defined Messages Supported", and there were no supported VDMs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.18
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.34.1002:**
      
        * An issue where set_flow_table_entry failed when aso_flow_meter action was used.
        * A race condition that occured between the duplicate read and QP commands (2RST, 2ERR and Destroy) in the signature that caused the command to hang.
        * When all traffic applications sharing the same combination of <function, priority, side> were rate limited (for example by congestion control), this limit was enforced on other applications with different combinations of <function, priority, side> under the same VL. For example, requestor flows (RDMA-write) were limited to rate X, however, this rate was also enforced on a QP sending RDMA-read responses. This firmware version prevents rate limit enforcement on traffic applications which should not be limited.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.19
changelog:
  -     *Firmware for the following devices has been updated to 2.42.5044 :**
      
        * 779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
        * 779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)
      
      **Firmware for the following devices has been updated to 14.32.1010:**
      
        * 817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
        * 817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)
      
      **Firmware for the following device has been updated to 16.35.1012:**
      
        * 874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.19
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * Bad configuration of number of VFs and SFs led to the consumption of too many functions and triggered a FW assert 0x888E. The reduction flows behavior was fixed to ensure the configuration does not exceed the total number of supported functions. 
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.20
changelog:
  -     *The following issues have been fixed in version 2.42.5044 :**
      
        * An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.
      
      **The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      **The following issues have been fixed in version 16.35.3006:**
      
        * Packet loss that occurred when restarting the transmit. 
        * An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
        * A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
        * Added a missing VLAN strip.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Firmware for the following devices are updated to 20.25.7020:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port 940QSFP56 x16 Adapter
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port 940QSFP56 x16 Adapter
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port 940QSFP56 x16 Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *New features and Changes added in firmware version 20.27.1016:**
      
        * RoCE Selective Repeat : This feature introduces a new QP (Queue Pair) retransmission mode in RoCE: recovery from packet drop by resending the dropped packet and not only all the PSN window (Go-Back-N protocol),  
      This new capability comes with the following limitations:
      
          * Selective repeat cannot be used with AR.
          * Does not work with signature (T10-DIF).
          * Does not work with Tag Matching enabled.
        * Allows BMC (Board Management Control) to query and control NIC over RedFish API. Currently, the NIC supports reading data and setting basic Ethernet and InfiniBand parameters.
        * Enables matching of source_vhca_port in the FDB also known as FIB ( Forwarding Information Base) flow for ECMP (Equal Cost Multi Pathing) hardware offload on a single FDB.
        * Firmware can be now updated as well as DB strings while performing Live Firmware Patch.
        * 100GbE link speed is supported in Auto-Negotiation Mode.
        * 200GbE link speed is supported in Force Mode.
        * Added support for the following: 
          * Dumping hardware steering entries (raw data) using the resource dump API
          * A new field in the PTYS register (max_port_rate).
          * Relaxed ordering read when using the create_mkey flag
          * DCQCN (Data Center and Quantized Congestion Notification) Congestion Control to ConnectX-6 InfiniBand adapter cards to improve application performance in case of congestion in the network.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Fixes submitted in version 20.27.1016:**
      
        * The Adapter card used to get stuck in "polling" state after resetting/power cycling the card.
        * Fixed a PCIe PLL (Phase Locked Loop) varactor calibration logic to address potential silicone variations.
        * An issue that caused the ZTR (Zero Touch RoCE) counters query to always return 0.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *New Features and Changes in Version 20.27.2008:**
      
        * 200GbE speed rate is at GA level.
        * All Ethernet speeds at GA level including PAM4(Pulse Amplitude Modulation) vs NRZ (non-return-to-zero)and speed detection.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *The following issues have been fixed in version 20.27.2008:**
      
        * CWDM4(Coarse Wavelength Division Multiplexing) Acousto Optical Modulator(AOM) cable was not supported.
        * Links between ConnectX-6 adapter cards and Spectrum-2 SN3700 switch systems did not come up when using Cisco BiDi module at 100GbE link speed.
        * Occasionally, the link was not raised when working with split 2x100 mode with Optical cables.
        * The PCIe Tx parameters did not load correctly when the speed was changed after the PCIe link was disabled.
        * The desched_threshold field did not work properly.
        * The "roce_adp_retrans" counter was presenting the values of the "local_ack_timeout_err" counter.
        * If Relaxed Ordering was disabled by running the "setpci" command, it would not be functional even after re-enabling it by running the "setpci" command again.
        * Aligned the User Memory page to 2, e.g., the user should use 8k aligned (like 0, 8k, 16k etc., instead of 0, 4k, 12k etc.).
        * NRZ (non-return-to-zero) and PAM4 (Pulse amplitude modulation) Limitations in 100GbE adapter cards: 
          * The default configuration was NRZ speeds in Auto-Neg mode.
          * PAM4 speeds had to be set manually (using the MFT tool - mlxlink).
          * PAM4 speeds had to be configured as single speeds: 50G_1x or 100G_2x.
          * 200G_4x optical cables (including 200G_4x splitter cable) would raise link only after manual configuration of PAM4 speeds (50G_1x or 100G_2x).
        * NRZ and PAM4 Limitations in 200GbE adapter cards: 
          * The default configuration was 200G_x4 in Force mode.
          * NRZ speeds had to be set manually. Configuration could include multiple NRZ speeds (using the MFT tool - mlxlink).
          * PAM4 speeds had to be configured as single speeds: 50G_1x or 100G_2x or 200G_4x.
        * In Ethernet mode, at 25/50/100GbE speeds, only RS-FEC in Force mode was supported. Other user configurations were overridden.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Firmware for the following devices are updated to 20.27.6008:**
      
      HPE InfiniBand HDR/Ethernet 200Gb 1-port 940QSFP56 x16 Adapter - P06154-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 1-port 940QSFP56 x16 Adapter - P06250-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 2-port 940QSFP56 x16 Adapter - P06251-B21  
      
      
      **New Features and Changes in Version 20.27.6008:**
      
        * The following are the minimal software/firmware versions that support PAM4 link speeds when connected using Mellanox NIC to Mellanox Switch and Mellanox NIC to 3rd Party Switches: 
          * Mellanox Onyx: 3.9.0830-038
          * ConnectX-6: 20.27.2008*  
      *Note: NICs with this firmware version support Mellanox-to-Mellanox connectivity with PAM4 link speeds.
        * Added support for the following features: 
          * Enabled KP4RS FEC on Active Fiber cable up to 30m.
          * FDR protocol.
          * Enabled updating End-to-End (E2E) credit packets instantly.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following devices are updated to 20.29.1016:**
      
      HPE InfiniBand HDR/Ethernet 200Gb 1-port 940QSFP56 x16 Adapter - P06154-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 1-port 940QSFP56 x16 Adapter - P06250-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 2-port 940QSFP56 x16 Adapter - P06251-B21  
      
      
      **New Features and Changes in Version 20.29.1016:**
      
      Added support for following features:
      
        * LinkX module burning via MFT toolset. The new capability enables direct firmware burning from the internal flash storage to reduce the bandwidth and accelerate the burning process, including burning several modules at a time.
        * An option to allow applications to build their own QoS tree over the NIC hierarchy by connecting QPs to responder/requestor Queue Groups.
        * Improved NRZ link performance (RX algorithm).
        * Improved NRZ link-up time (25G(G@G speeds).
        * Enabled the options to control different Tx sets for the same attribute when connecting a Mellanox-Mellanox vs Mellanox to 3rd party HCA.
        * "InfiniBand" properties set to the Network Device Function Redfish object.
        * Direct Packet Placement (DPP): DPP is a receive side transport service in which the Ethernet packets are scattered to the memory according to a packet sequence number (PSN) carried by the packet, and not by their arrival order.
        * To enable DPP offload, the software should create a special RQ by using the CREATE_RQ command, and set DPP relevant attributes.
        * Added trust level for VFs. Once the VF is trusted, it will get a set of trusted capabilities.
        * UCX can now enable AR by exposing Out-Of-Ordering bitmask per SL with "ooo_per_sl" field in the HCA_VPORT context. It can be also queried by running the QUERY_HCA_VPORT_CONTEXT command.
        * Enhanced IB Congestion Control to support lower minimum rate. Now it uses destination-lid to classify flows to handle larger scale, and achieve better results in GPCNeT benchmark.
        * Hardware steering dump output used for debugging and troubleshooting.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues have been fixed in version 20.29.1016:**
      
        * Changed the default value of DCQCN's (Data center- Quantized Congestion Notification) NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        * An issue that prevented VXLAN packets with svlan/cvlan tag from being matched.
        * The eth_wqe_too_small counter to count ODP (On-Demand Paging) page used to fail.
        * An issue related to raising 100GbE link on ConnectX-6 VPI 100Gb/s adapter cards.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs are configured, VM restart (VF/PF FLR) will take longer than when MKEY_BY_NAME is disabled.
        * Low performance occurred after enabling the RoCE Accelerator capability.
        * On rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *Firmware for the following devices are updated to 20.31.1014:**
      
      HPE InfiniBand HDR/Ethernet 200Gb 1-port 940QSFP56 x16 Adapter - P06154-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 1-port 940QSFP56 x16 Adapter - P06250-B21  
      HPE InfiniBand HDR100/Ethernet 100Gb 2-port 940QSFP56 x16 Adapter - P06251-B21
      
      **New features and changes included in version 20.31.1014:**
      
        * NIC scheduling feature support has been disabled for non-privileged functions.
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * Updated the NC-SI speed reporting output to support 200GbE speed. Now when running the NC-SI command, the output presents 200GbE speed as well.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Asymmetrical MSIX Configuration: This feature allows the device to be configured with a different number of MSIX vectors per physical PCI functions.To use this feature, please follow these steps: 
          * Clear NUM_PF_MSIX_VALID to disable global symmetrical MSIX configuration.
          * Set PF_NUM_PF_MSIX_VALID to enable asymmetrical per Physical Function MSIX configuration.
          * Configure PF_NUM_PF_MSIX per physical PCI function.
        * RDMA partitioning and RDMA counters in IB mode.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.
        * Enabled UID 0 to create resources with UMEM (User Memory).
        * Receiving and sending native IB packets from/to the software (including all headers) via raw IBL2 QPs.
        * RX RDMA NIC flow table on an IB port. Now the software can steer native IB packets to raw IB receive queues according to the DLID and  the DQPN.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *The following issues have been fixed in version 20.31.1014:**
      
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to unresponsive state.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
        * In InfiniBand non-virtualization system, due to a corrupted steering root, traffic fails after a warm reboot.  
      
                                                                               
      **Additional Fixes included in version 20.31.1014:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.            
        * Improved PortXmitWait IB counter accuracy.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *Firmware for the following devices has been updated to 20.32.1010:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06251-B21
      
      **New features and changes included in version 20.32.1010:**
      
        * Added support for blocking unwanted GMP classes by dedicated MADs.
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Added a Congestion Control Key to all Congestion Control MADs to authenticate that they are originated from a trusted source.
        * Added an SMP firewall to block the option of sending SMPs (MADS sent on QP0 from the Subnet Manager) from unauthorized hosts to prevent fake SMPs from being recognized as the SM.
        * Vendor Specific MADs Class 0x9 is no longer supported by the firmware. If case the firmware detects such MAD, the firmware will return a "NOT SUPPORTED" error to the user.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for dynamic timeout mechanism when in InfiniBand mode.
        * Added support for QSHR access register to enable Set and Query rate limit per-host per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Added support for asymmetrical VFs per PF. To enable it: PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a none zero value.
        * Added 2 new MAD access registers to enable mlxlink to read/write access registers by LID (to the whole subnet).
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.
        * Limited the external loopback speed according to the used module's capabilities.
        * Modified the Effective BER calculation method. Due to this, the value of the Effective BER will be slightly higher, however the link quality remains the same as prior to this change.
        * This firmware version includes the following PCIe changes: 
          * Fixed the ACS Port Number field in DSPs and ACS Egress Control Vector field in DSPs.
          * Added support for VSC on USP of PCIe Switch.
          * Fixed the mapping of Legacy Interrupts in the PCIe Switch.
          * Fixed MRRS & MPS configurations in DSPs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *The following issues have been fixed in version 20.32.1010:**
      
        * System could not create more than 128K QPs.
        * Incorrect indication of the PCIe link down in the AER registers on PCIe switch upstream port.
        * Invalid RNR timeout when trying to set it during the rts2rts_qp transition.
        * The flash frequency on boot was lower than expected (under 50Mhz). The issue was fixed by enabling the firmware to increase it on boot2 to normal frequency.
        * A race condition between DC QP flush and DC packets that led to stuck slices in the hardware. To avoid such situation, firmware keeps the TCU drop set until QP flush is done.
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Firmware for the following devices has been updated to 20.33.1048:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21
      
      **New features and changes included in version 20.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation. 
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter. 
        * Crypto features can be in either wrapped or unwrapped mode. Meaning, the key can be wrapped or in plaintext when running the CREATE_DEK PRM command. To comply with the requirements specified in FIPS publication, all the created DEKs must be wrapped.  
      This feature adds new NV_CONFIG per device to control this mode, and enables
      the user to change all the crypto features to wrapped or cleartext.
      
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *The following issues have been fixed in version 20.33.1048:**
      
        * An issue where RDMA write may experience performance degradation when working with Adaptive Routing and DCT half-handshake mode.
        * An issue that ignored the default value of TX_SCHEDULER_BURST when its value in the ini was different than "0".
        * Implemented SLD detection code. Surprise Down Error Reporting Capable value was changed from 1 to 0 in boards where the downstream perst was not controlled thus causing SLD detection not to function properly.
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * RDMA_WRITE traffic performance degradation that occured when working with DC on Adaptive Routing network.
        * Bad cache invalidations of destroyed QPs.
        * A rare case where asserts and ext_synd appeared in dmesg after performing driver restart. 
        * An issue related to host isolation on multi-host systems.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *Firmware for the following devices has been updated to 20.35.1012:**
      
        * HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
        * HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21
      
      **New features and changes included in version 20.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP
        * Added support for using SetEventReceiver PLDM command with mode polling.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *The following issues have been fixed in version 20.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * The RXT E2E inflight went into an unresponsive state occasionally.
        * RDMA partition was reported even if NIC+RDMA mode was disabled.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * An incorrect address issue for XRQ Event Backend Controller Px Syndrome event in multi-host system during FLR.
        * PCIe SKP OS generation interval issue for Gen1 and Gen2.
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.
        * PLDM AEN event receiver was required to be cleared on PCIe reset in case the media type was MCTP over PCIe VDM.
        * Asynchronous messages were sent over MTCP before endpoint discovery was done.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0
changelog:
  -     *Firmware for the following devices is updated to 14.26.1040 :**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
      
      **Firmware for the following devices is updated to 14.26.2000 :**
      
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.26.1040:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter )  
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCAT Adapter)
      
      **Firmware for the following devices is updated to 16.26.2000:**
      
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **New features and changes in version  14.26.1040 and 16.26.1040 :**
      
        * Enabled the firmware by using the ICMD commands to deal with diagnostic counters similar to cmdif. They can be called via the vsec space. The counters' values are returned only via the tracer. The ICMD Query Caps indicate support and expose the list of the supported counters.
        * Zero-Touch-RoCE counters are now available to the user for debuggability purposes when using the Zero-Touch-RoCE feature.
        * Added Address Translation Service (ATS) support for MKEY and UMEM VPD Added support for exposing the VPD on the VF.
        * Added support for the following 
          * Reporting the supported affiliated and unaffiliated asynchronous events to DEVX users through the command interface.
          * Hairpin Drop Counter.
          * Hairpin and TM RNDV QPs to work with DevX.
          * creating software managed steering tables in eSwitch/FD
      
      **New features and changes in version  14.26.2000 and 16.26.2000 :**
      
        * Live Firmware Patch (LFWP) allows applying of critical hot fixes without interrupting data traffic and without any user application interruptions


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0
changelog:
  -     *Fixes in version 14.26.2000 :**
      
        * Enabled the option to prevent clock and capture CPLD GPIOs glitch upon firmware reset.
      
      **Fixes in version 14.26.1040 :**
      
        * Fixed an issue that caused a function to misbehave when a PCIe Traffic Light Protocol(TLP) was set with a poisoned indication.
        * Fixed a rare issue that resulted in "destroy mkey " command getting stuck when rebooting the hypervisor.
      
      **Fixes in version 16.26.2000 :**
      
        * Enabled the option to prevent clock and capture CPLD GPIOs glitch upon firmware reset.
        * Fixed an issue that slowed the firmware flows when executing many destroy XRQ commands on an XRQ that supported DC transport service.
        * Fixed an issue that caused performance degradation when working in dual-port devices under bidirectional traffic stress.
      
      **Fixes in version 16.26.1040 :**
      
        * On rare occasions, when firmware coalesce Host stuck events occur, a async event might be delayed to be reported, and not be triggered until the next time the PCIe hangs on one of the hosts.
        * Fixed an issue that resulted in unexpected queue pairs transitioned to error in lossy tests.
        * Limited the maximum amount of dumps created on a Physical Function(PF).
        * Renamed the GMP Mellanox Vendor Specific External Capability mask enum from IsDiagnosticCountersSupported to IsDiagnosticDataSupported.
        * Fixed a stability issue in RoCE retransmissions under stress affecting Zero-Touch-RoCE.
        * Fixed an issue that caused a function to misbehave when a PCIe TLP was set with a poisoned indication.
        * Fixed an issue that caused large number of packet to drop when running Jumbo frames with Time to live (TTL) rewrite
        * Limited the number of the elements in the QoS tree 2K. Creating more than 250 Vport_tc for every TC was not allowed
        * Fixed the query QP flow. Instead of always taking port 1, FW will now reply the proper port, 1 or 2, for the dual port RDMA over Converged Ethernet(RoCE) net device.
        * Fixed an issue that caused the nack counters to constantly be reported as "0". 
        * In a rare scenario when the driver was executing the "2err" command and th Queue pair(QP) was in SQ drain state, the firmware might post event of broken Work Queue (WQ) instead of sending error CQEs on all the WQEs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0-2.1
changelog:
  -     *Firmware for the following devices is updated to 14.26.1040 :**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
      
      **Firmware for the following devices is updated to 14.26.2002 :**
      
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.26.1040:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter )  
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCAT Adapter)
      
      **Firmware for the following devices is updated to 16.26.2002:**
      
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **New features and changes in version  14.26.1040 and 16.26.1040 :**
      
        * Enabled the firmware by using the ICMD commands to deal with diagnostic counters similar to cmdif. They can be called via the vsec space. The counters' values are returned only via the tracer. The ICMD Query Caps indicate support and expose the list of the supported counters.
        * Zero-Touch-RoCE counters are now available to the user for debuggability purposes when using the Zero-Touch-RoCE feature.
        * Added Address Translation Service (ATS) support for MKEY and UMEM VPD Added support for exposing the VPD on the VF.
        * Added support for the following 
          * Reporting the supported affiliated and unaffiliated asynchronous events to DEVX users through the command interface.
          * Hairpin Drop Counter.
          * Hairpin and TM RNDV QPs to work with DevX.
          * creating software managed steering tables in eSwitch/FD
      
      **New features and changes in version  14.26.2002 and 16.26.2002 :**
      
        * Live Firmware Patch (LFWP) allows applying of critical hot fixes without interrupting data traffic and without any user application interruptions


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.0-2.1
changelog:
  -     *Fixes in version 14.26.2002 :**
      
        * Updated the firmware behavior to report PLDM version 1.1.0 regardless of whether Redfish was enabled or not.
        * Enabled the option to prevent clock and capture CPLD GPIOs glitch upon firmware reset.
      
      **Fixes in version 14.26.1040 :**
      
        * Fixed an issue that caused a function to misbehave when a PCIe Traffic Light Protocol(TLP) was set with a poisoned indication.
        * Fixed a rare issue that resulted in "destroy mkey " command getting stuck when rebooting the hypervisor.
      
      **Fixes in version 16.26.2002 :**
      
        * Updated the firmware behavior to report PLDM version 1.1.0 regardless of whether Redfish was enabled or not.
        * Enabled the option to prevent clock and capture CPLD GPIOs glitch upon firmware reset.
        * Fixed an issue that slowed the firmware flows when executing many destroy XRQ commands on an XRQ that supported DC transport service.
        * Fixed an issue that caused performance degradation when working in dual-port devices under bidirectional traffic stress.
      
      **Fixes in version 16.26.1040 :**
      
        * On rare occasions, when firmware coalesce Host stuck events occur, a async event might be delayed to be reported, and not be triggered until the next time the PCIe hangs on one of the hosts.
        * Fixed an issue that resulted in unexpected queue pairs transitioned to error in lossy tests.
        * Limited the maximum amount of dumps created on a Physical Function(PF).
        * Renamed the GMP Mellanox Vendor Specific External Capability mask enum from IsDiagnosticCountersSupported to IsDiagnosticDataSupported.
        * Fixed a stability issue in RoCE retransmissions under stress affecting Zero-Touch-RoCE.
        * Fixed an issue that caused a function to misbehave when a PCIe TLP was set with a poisoned indication.
        * Fixed an issue that caused large number of packet to drop when running Jumbo frames with Time to live (TTL) rewrite
        * Limited the number of the elements in the QoS tree 2K. Creating more than 250 Vport_tc for every TC was not allowed
        * Fixed the query QP flow. Instead of always taking port 1, FW will now reply the proper port, 1 or 2, for the dual port RDMA over Converged Ethernet(RoCE) net device.
        * Fixed an issue that caused the nack counters to constantly be reported as "0". 
        * In a rare scenario when the driver was executing the "2err" command and th Queue pair(QP) was in SQ drain state, the firmware might post event of broken Work Queue (WQ) instead of sending error CQEs on all the WQEs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Firmware for the following devices is updated to 14.26.4012:**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
      
      **Firmware for the following devices is updated to 14.26.6000 :**
      
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.26.4012:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter )  
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCAT Adapter)
      
      **Firmware for the following devices is updated to 16.26.6000:**
      
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **New features and changes in version  14.26.4012 and 16.26.4012 :**
      
        * Enabled the firmware by using the ICMD commands to deal with diagnostic counters similar to cmdif. They can be called via the vsec space. The counters' values are returned only via the tracer. The ICMD Query Caps indicate support and expose the list of the supported counters.
        * Zero-Touch-RoCE counters are now available to the user for debuggability purposes when using the Zero-Touch-RoCE feature.
        * Added Address Translation Service (ATS) support for MKEY and UMEM VPD Added support for exposing the VPD on the VF.
        * Added support for the following 
          * Reporting the supported affiliated and unaffiliated asynchronous events to DEVX users through the command interface.
          * Hairpin Drop Counter.
          * Hairpin and TM RNDV QPs to work with DevX.
          * creating software managed steering tables in eSwitch/FD
      
      **New features and changes in version  14.26.6000 and 16.26.6000 :**
      
        * Explicit Congestion Notification (_ECN_) is now automatically copied from the inner header to the outer header, unless defined otherwise in the SW steering. To disable this feature, need to write to the NV_SW_OFFLOAD_CONFIG file.
        * The eth_link_down_counter now counts logical link downs as well


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.1
changelog:
  -     *Fixes in version 14.26.6000 :**
      
        * Fixed an issue that cause the firmware to hang when an FLR occurred at the same time as the teardown. As a result, the teardown flow took a lock, and never  released it because it was being aborted by an FLR.
      
      **Fixes in version 14.26.4012 :**
      
        * Updated the firmware behavior to report PLDM version 1.1.0 regardless of whether Redfish was enabled or not.
        * Enabled the option to prevent clock and capture CPLD GPIOs glitch upon firmware reset.
        * Fixed an issue that caused a function to misbehave when a PCIe Traffic Light Protocol(TLP) was set with a poisoned indication.
        * Fixed a rare issue that resulted in "destroy mkey " command getting stuck when rebooting the hypervisor.
      
      **Fixes in version 16.26.6000 :**
      
        * Fixed an issue that prevented PCI link from being established when the firmware was corrupted.
        * Fixed an issue that triggered a firmware assert and resulted in a wrong deallocation of a resource when Packet Pacing was enabled, and a QP was being destroyed.
        * Fixed an issue that cause the firmware to hang when an FLR occurred at the same time as the teardown. As a result, the teardown flow took a lock, and never  released it because it was being aborted by an FLR.
      
      **Fixes in version 16.26.4012:**
      
        * Updated the firmware behavior to report PLDM version 1.1.0 regardless of whether Redfish was enabled or not.
        * Enabled the option to prevent clock and capture CPLD GPIOs glitch upon firmware reset.
        * Fixed an issue that slowed the firmware flows when executing many destroy XRQ commands on an XRQ that supported DC transport service.
        * Fixed an issue that caused performance degradation when working in dual-port devices under bidirectional traffic stress.
        * On rare occasions, when firmware coalesce Host stuck events occur, a async event might be delayed to be reported, and not be triggered until the next time the PCIe hangs on one of the hosts.
        * Fixed an issue that resulted in unexpected queue pairs transitioned to error in lossy tests.
        * Limited the maximum amount of dumps created on a Physical Function(PF).
        * Renamed the GMP Mellanox Vendor Specific External Capability mask enum from IsDiagnosticCountersSupported to IsDiagnosticDataSupported.
        * Fixed a stability issue in RoCE retransmissions under stress affecting Zero-Touch-RoCE.
        * Fixed an issue that caused a function to misbehave when a PCIe TLP was set with a poisoned indication.
        * Fixed an issue that caused large number of packet to drop when running Jumbo frames with Time to live (TTL) rewrite
        * Limited the number of the elements in the QoS tree 2K. Creating more than 250 Vport_tc for every TC was not allowed
        * Fixed the query QP flow. Instead of always taking port 1, FW will now reply the proper port, 1 or 2, for the dual port RDMA over Converged Ethernet(RoCE) net device.
        * Fixed an issue that caused the nack counters to constantly be reported as "0". 
        * In a rare scenario when the driver was executing the "2err" command and th Queue pair(QP) was in SQ drain state, the firmware might post event of broken Work Queue (WQ) instead of sending error CQEs on all the WQEs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Firmware for the following devices is updated to 14.27.1016:**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)  
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.27.1016:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter)  
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)  
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **New features and changes in version 14.27.1016 and 16.27.1016:**
      
        * RoCE Selective Repeat introduces a new QP retransmission mode in RoCE: recovery from packet drop by resending the dropped packet and not only all the PSN window (Go-Back-N protocol). This new capability comes with the following limitations:  
                 Selective repeat cannot be used with AR  
                 Does not work with signature (T10-DIF)  
                 Does not work with Tag Matching enabled
        * Allows BMC to query and control NIC over RedFish API (https://www.dmtf.org/standards/redfish). Currently, the NIC supports reading data and setting basic Ethernet and InfiniBand parameters
        * Enables matching of source_vhca_port in the FDB flow for ECMP hardware offload on a single FDB.
        * Firmware can be now updated as well as DB strings while performing Live Firmware Patch.
        * Added support for dumping hardware steering entries (raw data) using the resource dump API.
        * The eth_link_down_counter now counts logical link downs as well.
        * Enables the device to generate events that will notify the user about any resource dumps updates. The resource dump owner (PF/ECPF) will be notified on the VF command failures by events that will contain the needed information to call the resource_dump command. The device will dump the resource in the standard resource dump sequence.
        * Added support for RSS based on inner headers of GTP-U tunneled packets.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.2
changelog:
  -     *Fixes in version 14.27.1016:**
      
        * The device to perform Direct memory access (DMA) into memory already returned to the OS during the transition between the pre-boot drivers to the OS driver.
        * Fixed a rare issue that resulted in HCA hanging during a FlexibleLOM (FLR) flow while unloading the PreBoot driver.
        * The Zero-Touch RoCE (ZTR) counters query to always return 0.
        * Fixed a performance degradation issue, and a high packet drop when single root input/output virtualization or SR-IOV was enabled and packets went through the FDB default behavior.
        * Network Controller Sideband Interface (NC-SI) bandwidth dropping to 20-40kBps with a high amount of package drops, in a network environment with high latency (over 110ms).
        * Due to the string DB not being updated after Live-Patch, the tracer cannot function after Live-Patch.
        * Fixed a issue that caused other active functions to receive a malformed Completion with Error (CQE) during driver (PF or VF) unload or FLR flows.
        * Prevented the adapter card from going into the bypass mode when the Board Management Controller (BMC) disabled the hardware arbitration.
        * The firmware to hang when an FLR occurred at the same time as the teardown. As a result, the teardown flow took a lock, and never released it because it was being aborted by an FLR.
      
      **Fixes in version 16.27.1016:**
      
        * Fixed an issue that in Multi-Host adapter cards that resulted in wrong handling of PCIe Reset(PERST) on auxiliary links.
        * Fixed an out-of-range issue when reading or writing the q_counters.
        * The device to perform DMA into memory already returned to the OS during the transition between the pre-boot driver to the OS driver.
        * The ZTR counters query to always return 0.
        * That prevented the adapter card from going into the bypass mode when the BMC disabled the hardware arbitration.
        * Required using a non-standard tool to perform the first Live Firmware Patch Update (LFWP) patching when used the GA firmware version.
        * Fixed redundant page consumption in the init_hca.
        * The sw_reset option was not supported when ATS was enabled.
        * Fixed a possible performance degradation in small packet sizes that occured when SWITCH_IPV4_TTL_MODIFY_ENABLE configuration was enabled in mlxconfig.
        * Due to the string DB not being updated after Live-Patch, the tracer cannot function after Live-Patch.
        * Other active functions to receive a malformed CQE during driver (PF or VF) unload or FLR flows.
        * Prevented PCI link from being established when the firmware was corrupted.
        * Triggered a FW assert and resulted in a wrong deallocation of a resource when Packet Pacing was enabled and a QP was being destroyed.
        * The firmware to hang when an FLR occurred at the same time as the teardown. As a result, the teardown flow took a lock, and never released it because it was being aborted by an FLR.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Firmware for the following devices is updated to 14.27.4000:**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)  
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.27.2008:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter)  
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)  
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **New Feature and Changes in Version 12.27.4000:**
      
        * Added the following segments, as appeared in the PRM, to the Resource Dump: 
          * PRM_QUERY_QP
          * PRM_QUERY_CQ
          * PRM_QUERY_MKEY
          * QUERY_VNIC_ENV
      
      **New Feature and Changes in Version 16.27.2008:**
      
      **This release contains important reliability improvements and security hardening enhancements. Upgrade the firmware of the device to this release to improve the devices' firmware security and reliability.**
      
        * Improved init_hca performance in Parallel Function initialization.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.3
changelog:
  -     *Following issues have been fixed in firmware version 16.27.2008:**
      
        * Although the effective BER (after FEC) was expected to meet the design targets (e.g. 10e-14 or lower), occasionally it was higher.
        * High BER occured when connecting cables of type 0.5/1m DAC to an HDR speed.
        * The PCIe Tx parameters did not load correctly when the speed was changed after the PCIe link was disabled.
        * The desched_threshold field did not work properly.
        * The "roce_adp_retrans" counter was presenting the values of the "local_ack_timeout_err" counter.
        * If Relaxed Ordering was disabled by running the "setpci" command, it would not be functional even after re-enabling it by running the "setpci" command again.
      
      **Following issues have been fixed in firmware version 14.27.4000:**
      
        * The device hung while running the sw reset flow under heavy stress and with many open resources.
        * Low PXE performance observerd while using the VSC to trigger the send_ring_doorbells.
        * IPoIB and DC would not work together.
        * DC funtionality issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Firmware for the following devices is updated to 14.29.1016:**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)  
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.29.1016:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter)  
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)  
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **This release contains important reliability improvements and security hardening enhancements. Upgrade the firmware of the device to this release to improve the devices' firmware security and reliability.**
      
      **New Feature and Changes in Version 14.29.1016 and 16.29.1016:**
      
        * Ethernet wqe_too_small Mode: A per vPort that counts the number of packets that reached the Ethernet RQ but cannot fit into the WQE due to their large size. Additionally, we added the option to control if such packet will cause "CQE with Error" or "CQE_MOCK".
        * Hardware steering dump output used for debugging and troubleshooting.
      
      Added support for the following features:
      
        * cq_overrun counter: The counter represents the number of times CQs enter an error state due to overflow that occur when the device tries to post a CQE into a full CQ buffer.
        * Enabled the capability to allow Virtual Functions to send Pause Frames packets. (Beta)
        * Enabled 10/25GbE auto-sensing with 3rd party when using 10/25GbE optical cables.
      
      **New Feature and Changes in Version 16.29.1016:**
      
        * Hardware steering dump output used for debugging and troubleshooting.
      
      Added support for the following features:
      
        * HW support for Flow Metering to utilize Advanced Steering Operation (ASO). HW Flow Meter allows higher scale, more accuracy, and better performance compare to the FW Flow Metering.
        * Trust level for VFs. Once the VF is trusted, it will get a set of trusted capabilities.
        * 2 new Mini CQE formats:
        * Responder Mini CQE With Flow Tag Layout.
        * Responder Mini CQE With l3_l4_info Layout.
        * Steering DP hash flow groups.
        * ignore_flow_level is now enabled by the TRUST LEVEL access registry.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4
changelog:
  -     *Following issues have been fixed in firmware version 14.29.1016 and 16.29.1016:**
      
        * Changed the default value of DCQCN's NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        * An issue that caused packets to drop due to header size issues and/or failing checks. This issue was caused due to a Linux issue that caused VFs to set the wrong header size value in wqe_inline_header_mode input.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs are configured, VM restart (VF/PF FLR) might take longer than when MKEY_BY_NAME was disabled.
        * In rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.
        * An issue that caused the device to go to dead IRISC as one of the firmware semaphores could not be released when a speed change or port state change was triggered.
      
      **Following issues have been fixed in firmware version 16.29.1016:**
      
        * An issue that caused the eth_wqe_too_small counter to count ODP page faults.
        * A low performance was observed after enabling the RoCE Accelerator capability.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-3.1
changelog:
  -     *Firmware for the following devices is updated to 14.29.1016:**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
      
      **Firmware for the following devices is updated to 14.31.1200:**  
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.29.1016:**
      
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      **This release contains important reliability improvements and security hardening enhancements. Upgrade the firmware of the device to this release to improve the devices' firmware security and reliability.**
      
      **New Feature and Changes in Version 14.29.1016 and 16.29.1016:**
      
        * Ethernet wqe_too_small Mode: A per vPort that counts the number of packets that reached the Ethernet RQ but cannot fit into the WQE due to their large size. Additionally, we added the option to control if such packet will cause "CQE with Error" or "CQE_MOCK".
        * Hardware steering dump output used for debugging and troubleshooting.
        * cq_overrun counter: The counter represents the number of times CQs enter an error state due to overflow that occur when the device tries to post a CQE into a full CQ buffer.
        * Enabled the capability to allow Virtual Functions to send Pause Frames packets. (Beta).
        * Enabled 10/25GbE auto-sensing with 3rd party when using 10/25GbE optical cables.
      
      **New Feature and Changes in Version 16.29.1016:**
      
        * Hardware steering dump output used for debugging and troubleshooting.
        * HW support for Flow Metering to utilize Advanced Steering Operation (ASO). HW Flow Meter allows higher scale, more accuracy, and better performance compare to the FW Flow Metering.
        * Trust level for VFs. Once the VF is trusted, it will get a set of trusted capabilities.
        * 2 new Mini CQE formats:
        * Responder Mini CQE With Flow Tag Layout.
        * Responder Mini CQE With l3_l4_info Layout.
        * Steering DP hash flow groups.
        * ignore_flow_level is now enabled by the TRUST LEVEL access registry. 
      
      **New Feature and Changes in Version 14.31.1200:**
      
        * Added a new NVconfig per Port for a specific Finisar module which sets the port to work in AN mode and sets the module to No DME. This change does not affect the speed logic, only the FEC logic (FEC override). **Note**: If the port does not come up, switch to Force mode.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-3.1
changelog:
  -     *Following issues have been fixed in firmware version 14.29.1016 and 16.29.1016:**
      
        * Changed the default value of DCQCN's NP parameter min_time_between_cnps to 4 on all devices to support larger scalability of cluster.
        * An issue that caused packets to drop due to header size issues and/or failing checks. This issue was caused due to a Linux issue that caused VFs to set the wrong header size value in wqe_inline_header_mode input.
        * When MKEY_BY_NAME was enabled by NVCONFIG and a large number of VFs are configured, VM restart (VF/PF FLR) might take longer than when MKEY_BY_NAME was disabled.
        * In rare cases, a fatal error related to errors from the PCI transport layer might be reported during FLR.
        * An issue that caused the device to go to dead IRISC as one of the firmware semaphores could not be released when a speed change or port state change was triggered.
      
      **Following issues have been fixed in firmware version 16.29.1016:**
      
        * An issue that caused the eth_wqe_too_small counter to count ODP page faults.
        * A low performance was observed after enabling the RoCE Accelerator capability.
      
      **No fixes are included in firmware version 14.31.1200.**


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Firmware for the following devices is updated to 16.28.4200:**
      
      P13188-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX512F-ACAT Adapter)  
      P10112-B21 (HPE Ethernet 10/25Gb 2-port SFP28 MCX562A-ACAI OCP3 Adapter)
      
      **New Feature and Changes in Version 16.28.4200:**
      
      **This release contains important reliability improvements and security hardening enhancements. Upgrade the firmware of the device to this release to improve the devices' firmware security and reliability.**
      
        * Enabled ASN1 and OCBB (DCi) MCTP HPE specific protocols.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.4-2.1
changelog:
  -     *Following issues have been fixed in firmware version 16.28.4200:**
      
        * Although the effective BER (after FEC) was expected to meet the design targets (e.g. 10e-14 or lower), occasionally it was higher.
        * High BER occured when connecting cables of type 0.5/1m DAC to an HDR speed.
        * The PCIe Tx parameters did not load correctly when the speed was changed after the PCIe link was disabled.
        * The desched_threshold field did not work properly.
        * The "roce_adp_retrans" counter was presenting the values of the "local_ack_timeout_err" counter.
        * If Relaxed Ordering was disabled by running the "setpci" command, it would not be functional even after re-enabling it by running the "setpci" command again.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *Firmware for the following devices is updated to 14.31.1014:**
      
      P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
      
      **Firmware for the following devices is updated to 14.31.1200:**
      
      P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      **Firmware for the following devices is updated to 16.31.1014:**
      
      P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.31.1014:**
      
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.
      
      **New features and changes included in version 14.31.1200:**
      
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.                                                                                                                                
        * Added a new NVconfig per Port for a specific Finisar module. This new NVconfig sets the port to work in AN mode and sets the module to No DME. This change does not affect the speed logic, only the FEC logic (FEC override). Note: If the port does not go up, switch to Force mode.                                                                                                                        
      
      **New features and changes included in version 16.31.1014:**
      
        * NIC scheduling feature support has been disabled for non-privileged functions.
        * Implemented a new NC-SI command get_debug_info to get mstdump via the NC-SI protocol to debug a device if the PCI link fails for any given reason.
        * support for Enabling/Disabling NIC and RDMA (port/partition) was included via the UEFI HII system settings.
        * Increased the maximum number of MSIX per VF to 127.
        * Asymmetrical MSIX Configuration: This feature allows the device to be configured with a different number of MSIX vectors per physical PCI functions.To use this feature, please follow these steps:
        *         Clear NUM_PF_MSIX_VALID to disable global symmetrical MSIX configuration.
        *         Set PF_NUM_PF_MSIX_VALID to enable asymmetrical per Physical Function MSIX configuration.
        *         Configure PF_NUM_PF_MSIX per physical PCI function.
        * RDMA partitioning and RDMA counters in IB mode.
        * Added a new bit ("data_in_order") to query the QP and allow a process/library to detect when the AR is enabled.
        * A new flex parser to support GENEVE hardware offload and ICMP.
        * When the non-page-supplier-FLR funcion is initiated, the firmware triggers a page event to the page supplier to indicate that all pages should be returned for the FLR function.
        * Enabled UID 0 to create resources with UMEM (User Memory).
        * Receiving and sending native IB packets from/to the software (including all headers) via raw IBL2 QPs.
        * RX RDMA NIC flow table on an IB port. Now the software can steer native IB packets to raw IB receive queues according to the DLID and  the DQPN.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.5
changelog:
  -     *The following issues have been fixed in version 14.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1014:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.
      
      
      
      **The following issues have been fixed in version 14.31.1200:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
      
      **Additional Fixes included in version 14.31.1200:**
      
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.  
      
      
      **The following issues have been fixed in version 16.31.1014:**
      
        * TX PRBS was not changed even after reconfiguring it, all PRBS mode were enabled in test mode.
        * An assert that was caused when trying to open 1024 functions on the device and the maximum number of functions was 1023.
        * Occasional performance issues related to RC QPs using E2E-credits (not connected to SRQ and doing send/receive traffic) when the ROCE_ACCL tx_window was enabled.
        * A fatal error occurred and eventually resulted in the HCA to get into an unresponsive state when a packet was larger than a strided receive WQE that was being scattered.
        * A rare issue that caused RX pipe to hang.
        * The resource number size (a 64 bit number) was overwritten with a 32 bit number and erased the high bits when de-allocating the resource number.
        * CRT_DCR with index larger than 1 << 21 occasionally collided with the CRT_SW_RESERVED address.
        * An issue that caused the TX queue to get into an unresponsive state when the VF rate limiter was set.
      
      **Additional Fixes included in version 16.31.1014:**
      
        * Disabled the CNP counter "rp_cnp_ignored " (triggered by OOS (out-of-sequence)) when all ports are IB.
        * Fixed the TMP421 sensor temperature reporting.
        * Fixed the rate select mechanism in QSFP modules.
        * Fixed classification issues for "Passive" cables to be more robust.
        * Initialized the rate table in the static configuration so it will be configured at the link-not-up scenarios.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.32.1010:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.32.1010:**
      
        * Added a new NvConfig parameter LOG_MAX_QUEUE to set the maximum number of work queue resources (QP, RQ, SQ...) that can be created per function. The default value is 2^17.
        * Blocked the VF's ability to use both padding and signature in order to prevent the NIC from getting into an unresponsive state.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
        * Performance improvements in the DCT with AR flow by exposing a hint to the software in DCI software context that indicates that RDMA WRITE on this DCI is not supported.
        * Added support for QSHR access register to enable Set and Query rate limit perhost per-port.
        * The firmware now exposes a new Software Steering ICM resource for VXLAN encap expand in order for the SW Steering to manage this resource directly.
        * Enabled the exposure of new ICM resource to the software steering for VXLAN encapsulation expansion.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for DSFP AOC (CMIS) v4 when error code is not reported by the module.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.6
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The link status was reported incorrectly and consequently caused the link to go down due to incorrect definition of the RX_LOS polarity in the INI.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * The system could not create more than 128K QPs.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
        * PCIe lane margining capability issues.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.33.1048:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.
      
      .  
      
      **New features and changes included in version 16.33.1048:**
      
        * Added pci_rescan_needed field to the MFRL access register to indicate whether a PCI rescan is needed based on the NV configurations issued by the software.  
      Note: If the Keep Link Up NV configuration is changed, phyless reset will be
      blocked.
      
        * Added a new MAD of class SMP that has the attributes hierarchy_Info as defined in the IB Specification and is used to query the hierarchy information stored on the node and the physical port.
        * Added a new register (vhca_icm_ctrl access_reg) to enable querying and limiting the ICM pages in use.
        * Enhanced the XRQ QP error information provided to the user in case QP goes into an error state. In such case, QUERY_QP will provide information on the syndrome type and which side caused the error.
        * Replaced the deprecated NetworkPort schema with Port schema in NIC RDE implementation.
        * Updated the ibstat status reported when the phy link is down. Now QUERY_VPORT_STATE.max_tx_speed of UPLINK will not be reported as 0 anymore.
        * Disabled the option to send SMPs from unauthorized hosts.
        * Enabled the option to modify the ip_ecn field in the packet header in firmware steering.
        * Modified the TX or RX cache invalidation behavior. TX or RX cache invalidation now does not occur automatically but only when the software performs the sync operation using the using sync_steering command.
        * Modified the maximum bulk size per single allocation from "log_table_size - log_num_unisizes", to allocate any range size, to remove limitations that HWS objects such as counters and modify arguments might encounter.
        * Enabled delay drop for hairpin packets. If a hairpin QP is created with delay_drop_en enabled, the feature will be enabled across all GVMIs, based on the delay drop status.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.7
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.
      
      
      
      **The following issues have been fixed in version 16.33.1048:**
      
        * Rare lanes skew issue that caused CPU to timeout in Rec.idle.
        * The card occasionally masked some PCIe AER reporting.
        * Incorrect flow of credits blockage that prevented booting during DC cycle test.
        * An issue with BMC medium migration from SMBUS to PCIe, and increased FIFOs to pass large packets in case of the migration.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.34.1002:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.  
      
      
      **New features and changes included in version 16.34.1002:**
      
        * Added LLDPEnable, LLDPTransmit and LLDPReceive properties to the RDE Port schema implementation.
        * Added "Command Unsupported" response code in cases when running the MCTP control command "Get Vendor Defined Messages Supported", and there were no supported VDMs.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.8
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.  
      
      
      **The following issues have been fixed in version 16.34.1002:**
      
        * An issue where set_flow_table_entry failed when aso_flow_meter action was used.
        * A race condition that occured between the duplicate read and QP commands (2RST, 2ERR and Destroy) in the signature that caused the command to hang.
        * When all traffic applications sharing the same combination of <function, priority, side> were rate limited (for example by congestion control), this limit was enforced on other applications with different combinations of <function, priority, side> under the same VL. For example, requestor flows (RDMA-write) were limited to rate X, however, this rate was also enforced on a QP sending RDMA-read responses. This firmware version prevents rate limit enforcement on traffic applications which should not be limited.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *Firmware for the following devices has been updated to 14.32.1010:**
      
        * P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
        * P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)
      
      
      
      **Firmware for the following device has been updated to 16.35.1012:**
      
        * P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)
      
      
      
      **New features and changes included in version 14.32.1010:**
      
        * Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
        * Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its  rate limit.
        * Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
        * Limited the external loopback speed to the used module's capabilities.
        * Improved linkup time when using the fast linkup capability.
        * Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.  
      
      
      **New features and changes included in version 16.35.1012:**
      
        * Added support for copy modify header steering action to/from the UDP field.
        * Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
        * QoS priority trust default state can now be changed using the new nvconfig below: 
          * QOS_TRUST_STATE_P1
          * QOS_TRUST_STATE_P2
      
      The values that can be used to set the default state are:
      
        * TRUST_PORT
        * TRUST_PCP
        * TRUST_DSCP
        * TRUST_DSCP_PCP


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.9
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.  
      
      
      **The following issues have been fixed in version 16.35.1012:**
      
        * RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
        * PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
        * Bad configuration of number of VFs and SFs led to the consumption of too many functions and triggered a FW assert 0x888E. The reduction flows behavior was fixed to ensure the configuration does not exceed the total number of supported functions. 
        * InfiniBand L2 QP could not receive RDMA traffic occasionally.
        * Running with a debug firmware reduced security as if token was applied.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.10
changelog:
  -     *The following issues have been fixed in version 14.32.1010:**
      
        * Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
        * The system could not create more than 128K QPs.
        * On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
        * Packet Pacing rate was used if asymmetric VFs was enabled.
        * Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
        * Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
        * The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.  
      
      
      **The following issues have been fixed in version 16.35.3006:**
      
        * Packet loss that occurred when restarting the transmit. 
        * An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
        * A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
        * Added a missing VLAN strip.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.0.22
changelog:
  -     The firmware in this product addresses intermittent PCIe enumeration issues
      seen after warm/cold boot.
      
      The firmware in this product addresses a system crash seen when enabling NPAR
      with SRIOV enabled.
      
      The firmware in this product addresses an issue where a "NIC Initialization
      error" message is observed when PXE boot is attempted multiple times.
      
      The firmware in this product addresses an issue where the NCSI pass-through
      does not function when configured for DHCP IP.
      
      The firmware in this product addresses an issue where PXE boot fails in legacy
      boot mode.
      
      Ths firmware in this product addresses an issue where the system PXE boots
      when PXE boot is disabled on the port.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.1.29
changelog:
  -     This product now supports the following network adapters:
      
        * HPE Ethernet 10Gb 2-port 521T Adapter
        * HPE Ethernet 10Gb 2-port 522FLR-T Converged Network Adapter
        * HPE Ethernet 10/25Gb 2-port 621SFP28 Adapter
        * HPE Ethernet 10/25Gb 2-port 622FLR-SFP28 Converged Network Adapter
        * HPE Synergy 6810C 25/50Gb Ethernet Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.2.14
changelog:
  -     This product addresses an issue where the Wake-On-Lan setting on the second
      port isn't correctly enabled when the network adapter's configuration settings
      are restored to default in the 'System Utilities' (F9 on POST) under the
      'System Configuration' menu.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.3.12
changelog:
  -      This product addresses an issue where the inlet temperature is incorrectly reported.
        * This product addresses an issue where the Wake-On-LAN setting is not properly set on the second port after the defaults are restored.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.4.24
changelog:
  -      This product corrects an issue where booting to Preboot eXecution Environment (PXE) may not work after applying the OneView server profile when the System ROM is set to 'Legacy BIOS Mode'.
        * This product addresses an issue where the FCoE boot parameters cannot be configured in the adapter's configuration menu (under 'System Utilities'->'System Configuration' menu) when OneView profile with connections set to 'manually managed' is applied to the system.
        * This product corrects an issue where certain settings/changes (CHAP, boot mode etc) in the OneView server profile are not reflected in the adapters' configuration menu (under 'System Utilities'->'System Configuration' menu) after applying the OneView server profile.
        * This product corrects an issue where the virtual World Wide Port Name(WWPN)/World Wide Node Name(WWNN) are not programmed properly when applying the OneView server profile.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.4.65
changelog:
  -     This product now supports SUSE Linux Enterprise Server 15.
      
      This product now supports the following network adapters:
      
        * HPE Synergy 4820C 10/25Gb Converged Network Adapter
        * HPE StoreFabric CN1200R-T Converged Network Adapter
        * HPE StoreFabric CN1300R Converged Network Adapter


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.6.27
changelog:
  -     This product corrects an issue where the WWPN information is missing in an
      adapter's FCoE configuration menu (under 'System Utilities'->'System
      Configuration' menu).  
      This product corrects an issue where server hangs during POST when a network
      adapter is connected to the HPE Synergy 20Gb Interconnect Link Module.  
      This product corrects an issue where the initiator does not stay logged into
      the target in an FCoE connection.  
      This product corrects an issue where the link status continues to show as UP
      on the switch side even after a network adapter is disabled in the OS.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.7.16
changelog:
  -     This product now supports the HPE Synergy 6820C 25/50Gb Converged Network
      Adapter.
      
      This product now allows modification of the settings under the 'Port Level
      Configuration' sub-menu under the adapter's configuration menu (located at
      'System Utilities'(F9 at POST)->'System Configuration') when OneView Profile
      with 'manage manually' option is applied to the server.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.7.16
changelog:
  -     This product corrects an issue where the firmware update fails when the first
      port is disabled on the network adapter.
      
      This product corrects an issue where not all devices are discovered as part of
      firmware update on a multi-root-complex platforms like Integrity, Superdome
      etc.
      
      This product corrects an issue where the system hangs during POST with red
      screen when iSCSI boot LUN is re-exported (after a previous unexport
      operation) from the iSCSI host (HPE 3PAR StoreServ Storage).
      
      This product corrects an issue where 'HPE Synergy 4820C 10/20/25Gb Converged
      Network Adapter' disappears after changing its link speed under its
      configuration menu (located at 'System Utilities'(F9 at POST)->'System
      Configuration').
      
      This product corrects an issue where the configuration settings of the
      adapter, connected to a server managed by OneView profile, may be reset to
      defaults after a system reboot.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.8.12
changelog:
  -     This product addresses an issue where 2nd port reports "function type:
      disabled" with HPE Ethernet 10Gb 2-port 524SFP+ Adapter.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.9.8
changelog:
  -      This product corrects the abnormal disconnection of iLO web page while performing under Shared Networking on Flexible-LOM.
        * This product addresses an issue where the HPE Ethernet 10/25Gb 2-port 622FLR-SFP28 adapter and  HPE Ethernet 10/25Gb 2-port 621SFP28 Adapter UMCE (Uncorrectable Machine Check Exception) was followed by Unrecoverable I/O error, Uncorrectable PCI express error on Server and one of the ports suddenly no longer can send or receive traffic.
        * This product addresses an issue where driver doesn't load upon booting up by correct memory relocation.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.11.0
changelog:
  -     This product addresses an issue where the modification on string format of
      firmware update payload.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.21.3
changelog:
  -     This product now supports Red Hat Enterprise Linux 8 Update 6, Liunx 9 and
      SUSE Linux Enterprise Server 15 Service Pack 4.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 1.22.0
changelog:
  -     This product addresses an issue where Max Number of Virtual Machine
      Queues/Physical Function shows zero value in AHS


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.15.19
changelog:
  -     This firmware provides a new option in the NIC ROM-Based Setup Utility (RBSU)
      menu (HP's UEFI System Utilities - F9 at POST) to allow enabling and disabling
      of HP shared memory features.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.16.21
changelog:
  -     This product addresses an issue where the Smartlink function does not work
      properly when System ROM's 'Boot Mode' is in 'Legacy BIOS Mode'.
      
      This product addresses the following issues seen with 'HP FlexFabric 20Gb
      2-port 630FLB Adapter':
      
         Fixes an issue where the Boot from SAN in Legacy mode fails (hang observed
      during OS boot) because the FCoE ROM doesn't correctly honor the link status
      set by the Virtual Connect Manager.
      
         Fixes an issue where UEFI FCoE boot path sends false notification to MFW
      (Management Firmware) about the virtual function link change which eventually
      results in a deadlock with virtual link down.
      
         Fixes an issue where the fallback Boot from SAN fails even though each
      port is mapped to different Virtual Connect Bays and only one of the bays is
      powered off.


author: HP Linux Development <Linux_SWdeliverables@external.groups.hpe.com> 2.17.16
changelog:
  -     This product now supports the HPE StoreFabric CN1100R-T Converged Network
      Adapter.
      
      This product now provides the capability of converting an 'HP FlexFabric 10Gb
      2-port 533FLR-T Adapter' into a Converged Network Adapter.


